HP StorageWorks 1510i HP StorageWorks 1510i Modular Smart Array firmware 2.0 r - Page 6

To update MSA1510i firmware, rmware using the HP Storage Management Utility SMU

Get HP StorageWorks 1510i - Modular Smart Array PDF manuals and user guides View all HP StorageWorks 1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

2. Update the firmware using the HP Storage Management Utility (SMU): a. Point your browser to and open the SMU. b. Select the Configure tab. c. Select Controller (Active) > Flash Firmware. d. Click Browse, navigate to the location of the previously downloaded MSA20 firmware image file, and then select OK. Progress is indicated in the browser with "Flashing Firmware ........" e. Wait for the following popup message The operation completed successfully. The Storage system must be reset for the changes to take place." to display in the browser and for 313 FIRMWARE FLASH DONE ON BOX to display on the MSA1510i LCD panel. NOTE: If one or more MSA20 units are connected to the MSA1510i, each one is sequentially updated during this process. 3. Manually power cycle all attached MSA20s and wait for them to complete their startup processes. 4. In the SMU, select Storage System > Reset System to restart the MSA1510i. To update MSA1510i firmware, do the following: 1. In dual controller MSA1510i configurations, log off all of the redundant paths to the standby controller prior to beginning a firmware update. IMPORTANT: The update will NOT succeed if redundant paths are detected by the MPIO/DSM and may require multiple reboots to recover back to the original firmware version. There could also be potential loss of connection of the Internet Explorer to the management port if there are redundant paths during the flash update cycle. 2. Extract the MSA1510i firmware image file to a system folder. (The MSA1510i firmware filename will be in a format similar to V200B803_2008-0429.bin.) 3. Update the firmware using the HP Storage Management Utility (SMU) : a. Point your browser to and open the SMU. b. Select the Configure tab. c. Select Controller (Active) > Flash Firmware. d. Click Browse, navigate to the location of the previously downloaded MSA1510i firmware image file, and then select OK. Progress is indicated in the browser with "Flashing Firmware ........" e. Wait for the following popup message The operation completed successfully. The Storage system must be reset for the changes to take place." to display in the browser and for 313 FIRMWARE FLASH DONE ON BOX to display on the MSA1510i LCD panel. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
2.
Update the
fi
rmware using the HP Storage Management Utility (SMU):
a.
Point your browser to and open the SMU.
b.
Select the
Con
fi
gure
tab.
c.
Select
Controller (Active) > Flash Firmware
.
d.
Click
Browse
, navigate to the location of the previously downloaded MSA20
fi
rmware image
fi
le, and then select
OK
.
Progress is indicated in the browser with
"Flashing Firmware
........
"
e.
Wait for the following popup message
The operation completed successfully.
The Storage system must be reset for the changes to take place."
to
display in the browser and for
313 FIRMWARE FLASH DONE ON BOX <n>
to display on
the MSA1510i LCD panel.
NOTE:
If one or more MSA20 units are connected to the MSA1510i, each one is sequentially
updated during this process.
3.
Manually power cycle all attached MSA20s and wait for them to complete their startup processes.
4.
In the SMU, select
Storage System > Reset System
to restart the MSA1510i.
To update MSA1510i
fi
rmware, do the following:
1.
In dual controller MSA1510i con
fi
gurations, log off all of the redundant paths to the standby
controller prior to beginning a
fi
rmware update.
IMPORTANT:
The update will NOT succeed if redundant paths are detected by the MPIO/DSM and may
require multiple reboots to recover back to the original
fi
rmware version. There could also
be potential loss of connection of the Internet Explorer to the management port if there are
redundant paths during the
fl
ash update cycle.
2.
Extract the MSA1510i
fi
rmware image
fi
le to a system folder. (The MSA1510i
fi
rmware
fi
lename will
be in a format similar to
V200B803_2008–0429.bin
.)
3.
Update the
fi
rmware using the HP Storage Management Utility (SMU) :
a.
Point your browser to and open the SMU.
b.
Select the
Con
fi
gure
tab.
c.
Select
Controller (Active) > Flash Firmware
.
d.
Click
Browse
, navigate to the location of the previously downloaded MSA1510i
fi
rmware image
fi
le, and then select
OK
.
Progress is indicated in the browser with
"Flashing Firmware
........
"
e.
Wait for the following popup message
The operation completed successfully.
The Storage system must be reset for the changes to take place."
to
display in the browser and for
313 FIRMWARE FLASH DONE ON BOX <n>
to display on
the MSA1510i LCD panel.
6