HP StorageWorks SN6000 HP StorageWorks 8/20q Fibre Channel Switch CIM Agent re - Page 29

Not Supported: NS/Remote Ports Method applies to local ports, Use of Timeout Parameter Not Supported.

Get HP StorageWorks SN6000 - Fibre Channel Switch PDF manuals and user guides View all HP StorageWorks SN6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

EnableDefault (Local) Property contains the configured port state. • 02-Enabled: Port is enabled • 03-Disabled: Port is disabled (NS/Remote) • Property contains the enumerated value 5=Not Applicable. RequestStateChange (Local only) Method will change the configured port state to the RequestedState value. If the RequestedState parameter is 11-Reset, the port is reset, but the configured state will not change. Parameters: • RequestedState: [required] A port specific array of valid values may be found in the FCPortCapabilities.RequestedStatesSupported property. Parameter must be one of the following enumerated values. • 2-Enabled: Port is online. • 3-Disabled: Port is offline • 7-Test: Port is in diagnostics mode. • 11-Reset: Port is reset. • Job: Ignored, command is synchronous. • TimeoutPeriod: must be zero second interval, or NULL, command is synchronous. Method Returns: • 0-Success • 1-Not Supported: (NS/Remote Ports) Method applies to local ports only. • 6-In Use: Switch is being configured by another user. • 4097-Invalid State Transition: RequestedState parameter value is out of range. • 4098-Use of Timeout Parameter Not Supported. Request Status Codes: • CIM_ERR_ACCESS_DENIED: User does not have authorization for this command. • CIM_ERR_INVALID_PARAMETER: One or more required parameters are missing. • CIM_ERR_NOT_FOUND: The FCPort instance was not found. Extended properties and methods HealthState (Local Only) Property will report the diagnostic status of the port as a result of the switch POST. Supported values are: • 0-Unknown Port is not installed • 5-OK No errors • 25-Critical Failure Port failed POST IOStreamGuardState (Local Only) Property contains an enumerated value representing the operational state of the port IOStreamGuard feature. The property is used to detect what state the port is using when the FCPortSettings.IOStreamGuard property has been set to 1-AutoDetect. Supported values are: 8/20q Fibre Channel Switch CIM Agent reference guide 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
8/20q Fibre Channel Switch CIM Agent reference guide
29
EnableDefault
(Local)
Property contains the configured port state.
•
02
–
Enabled
: Port is enabled
•
03
–
Disabled
: Port is disabled
(NS/Remote)
•
Property contains the enumerated value
5=Not Applicable
.
RequestStateChange
(Local only)
Method will change the configured port state to the
RequestedState
value. If the
RequestedState
parameter is
11-Reset
, the port is reset, but the configured state will not
change.
Parameters:
•
RequestedState
: [required] A port specific array of valid values may be found in the
FCPortCapabilities.RequestedStatesSupported
property. Parameter must be one of
the following enumerated values.
•
2
–
Enabled
: Port is online.
•
3
–
Disabled
: Port is offline
•
7
–
Test
: Port is in diagnostics mode.
•
11
–
Reset
: Port is reset.
•
Job
: Ignored, command is synchronous.
•
TimeoutPeriod:
must be zero second interval, or NULL, command is synchronous.
Method Returns:
•
0-Success
•
1-Not Supported: (NS/Remote Ports) Method applies to local ports
only.
•
6-In Use: Switch is being configured by another user.
•
4097-Invalid State Transition: RequestedState parameter value is out
of range.
•
4098-Use of Timeout Parameter Not Supported.
Request Status Codes:
•
CIM_ERR_ACCESS_DENIED
: User does not have authorization for this command.
•
CIM_ERR_INVALID_PARAMETER
: One or more required parameters are missing.
•
CIM_ERR_NOT_FOUND
: The FCPort instance was not found.
Extended properties and methods
HealthState
(Local Only)
Property will report the diagnostic status of the port as a result of the switch POST. Supported values
are:
•
0-Unknown Port is not installed
•
5-OK No errors
•
25-Critical Failure Port failed POST
IOStreamGuardState
(Local Only)
Property contains an enumerated value representing the operational state of the port
IOStreamGuard
feature. The property is used to detect what state the port is using when the
FCPortSettings.IOStreamGuard
property has been set to
1
–
AutoDetect
.
Supported values are: