HP StorageWorks SN6000 HP StorageWorks Simple SAN Connection Manager user guid - Page 55

Select this option to use Dynamic Host Configuration Protocol for IPv6. DHCPv6 can

Get HP StorageWorks SN6000 - Fibre Channel Switch PDF manuals and user guides View all HP StorageWorks SN6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

• In the content pane's Physical Connection map, right-click a switch icon to select that specific switch, and then on the shortcut menu, click Set Switch IP Address. 2. If no specific switch is selected and if there is more than one switch in the SAN, the Switch Selection dialog box opens. Select the switch you want to change, and then click OK. The Set Switch IP Address dialog box (Figure 30) opens. Figure 30 Set Switch IP Address dialog box The dialog box shows the switch name and its current IP address on the top portion, and enables you to set either an IPv4 or IPv6 address for the switch on the bottom portion. 3. To set an IPv4 address for the switch, select the Enable IPv4 check box, and then enter a valid IPv4 address, subnet mask, and gateway in the appropriate boxes. 4. To set an IPv6 address for the switch, select the Enable IPv6 check box, and then complete the following for IPv6: a. From the IPv6 Discovery list, select one of the following: • Static-Select this option to enable the IPv6 address and gateway boxes and define those values. • DHCPv6-Select this option to use Dynamic Host Configuration Protocol for IPv6. DHCPv6 can be used to statefully assign addresses if the network administrator needs more control over addressing. It can also be used to distribute information that is not otherwise discoverable; for example, the DNS server. (If you select DHCPv6, the IPv6 address and gateway boxes become unavailable.) • NDP-Select this option to use Neighbor Discovery Protocol for IPv6, as part of the Stateless Address Autoconfiguration protocol. (If you select NDP, the IPv6 address and gateway boxes become unavailable.) b. If you selected Static for IPv6 Discovery, enter a valid address in the IPv6 Address box. HP StorageWorks Simple SAN Connection Manager user guide 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
HP StorageWorks Simple SAN Connection Manager user guide
55
•
In the content pane’s Physical Connection map, right-click a switch icon to select that specific switch,
and then on the shortcut menu, click
Set Switch IP Address
.
2.
If no specific switch is selected and if there is more than one switch in the SAN, the Switch Selection
dialog box opens. Select the switch you want to change, and then click
OK
.
The Set Switch IP Address dialog box (
Figure 30
) opens.
Figure 30
Set Switch IP Address dialog box
The dialog box shows the switch name and its current IP address on the top portion, and enables you to
set either an IPv4 or IPv6 address for the switch on the bottom portion.
3.
To set an IPv4 address for the switch, select the
Enable IPv4
check box, and then enter a valid IPv4
address, subnet mask, and gateway in the appropriate boxes.
4.
To set an IPv6 address for the switch, select the
Enable IPv6
check box, and then complete the following
for IPv6:
a.
From the IPv6 Discovery list, select one of the following:
•
Static
—Select this option to enable the IPv6 address and gateway boxes and define those
values.
•
DHCPv6
—Select this option to use Dynamic Host Configuration Protocol for IPv6. DHCPv6 can
be used to statefully assign addresses if the network administrator needs more control over
addressing. It can also be used to distribute information that is not otherwise discoverable; for
example, the DNS server. (If you select
DHCPv6
, the IPv6 address and gateway boxes become
unavailable.)
•
NDP
—Select this option to use Neighbor Discovery Protocol for IPv6, as part of the Stateless
Address Autoconfiguration protocol. (If you select
NDP
, the IPv6 address and gateway boxes
become unavailable.)
b.
If you selected
Static
for IPv6 Discovery, enter a valid address in the IPv6 Address box.