Home » HP Manuals » Storage Devices » HP StorageWorks SN6000 » Manual Viewer

HP StorageWorks SN6000 HP StorageWorks SN6000 QuickTools Switch management use - Page 53

NTP Client Enabled or Disabled. If Enabled, this parameter, Switch operational state: Online, Offline

View all HP StorageWorks SN6000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Table 9 Switch data window fields Field Description Operational State Switch operational state: Online, Offline, Diagnostic, Down Administrative State Current switch administrative state Configured Admin State Administrative state that is stored in the switch configuration Beacon Status Reason for Status Temperature Beacon status. Switch LEDs are blinking (On) or not blinking (Off). The reason for the operational state. Internal switch temperature °C Power Supply 1 Status Whether the switch is On or Off Temperature Failure Port Shutdown Non-configurable (always enabled for this switch). All ports are shut down when the switch temperature exceeds the Failure Temperature. Warning Temperature Failure Temperature POST Status Non-configurable temperature threshold (65° C), above which a warning condition alarm is generated. Non-configurable temperature threshold (70° C), above which a failure condition alarm is generated. The current diagnostic state of the switch. POST Fault Code The code value for the last recorded diagnostic test result recorded on the switch. Test Status The current diagnostic test status of switch. Test Fault Code Network Group IPv4 Enabled The code value for the last recorded diagnostic test status recorded on the switch. Internet Protocol version 4 Enabled or Disabled IPv4 Address Internet Protocol version 4 address IPv4 Subnet Mask Mask that determines the IP address subnet IPv4 Gateway Gateway address IPv6 Enabled IPv6 Address IPv6 Gateway Internet Protocol version 6 Enabled or Disabled Mask that determines the IP address subnet Gateway address SNMP Enabled SNMP Enabled or Disabled SNMP v3 Security Enabled SNMP v3 Security Enabled or Disabled Broadcast Support Broadcast support status. Broadcast support is enabled (default) or disabled. NTP Client Enabled NTP Server Address NTP Client Enabled or Disabled. If Enabled, this parameter enables switches to synchronize their time to a centralized server. The IP address of the centralized NTP server. Ethernet connection to NTP server is required. DNS Enabled Domain Name Service Enabled or Disabled HP StorageWorks SN6000 Fibre Channel Switch QuickTools Switch Management User Guide 53

Section	Page
Contents	3
About this guide	9
Intended audience	9
Prerequisites	9
Related documentation	9
Document conventions and symbols	10
Table 1 Document conventions	10
JDOM license	10
HP technical support	11
Subscription service	11
HP-authorized reseller	11
Helpful websites	12
Using QuickTools	13
Workstation requirements	13
Table 2 Workstation requirements	13
Opening QuickTools	13
Figure 1 Add a New Fabric dialog box	14
Figure 2 Password Change Required dialog box	14
QuickTools user interface	14
Figure 3 QuickTools interface	15
Fabric tree	15
Graphic window	15
Data windows and tabs	15
Alerts panel	16
Figure 4 Alerts panel	16
Menu bar	17
Table 3 Menu bar options	17
Popup menus	19
Shortcut keys	19
Selecting switches	19
Selecting ports	19
Setting QuickTools preferences	19
Figure 5 Preferences dialog box–QuickTools	20
Using online Help	20
Viewing the software version	20
Exiting QuickTools	21
Managing fabrics	23
Fabric services	23
Enabling SNMP configuration	23
Enabling in-band management	23
Rediscovering a fabric	23
Adding a new switch to a fabric	23
Replacing a failed switch	24
Transparent Router	24
TR Mapping Manager dialog	26
Figure 6 TR Mapping Manager dialog	26
Removing an inter-fabric route	26
Add TR Mapping dialog	27
Figure 7 Add TR Mapping dialog	27
Mapping a new inter-fabric zone	27
Remote Fabric Zoning dialog	28
Figure 8 Remote Fabric Zoning dialog	28
Transparent Routes data window	30
Figure 9 Transparent Routes data window	30
Table 4 Transparent Routes data window fields	30
Figure 10 Transparent Route dialog	31
Event Browser	31
Figure 11 Event Browser dialog box	32
Table 5 Port operational states	32
Filtering the Event Browser	33
Figure 12 Filter Events dialog box	33
Sorting the Event Browser	33
Saving the Event Browser to a file	34
Device information and nicknames	34
Devices data window	34
Figure 13 Devices data window	34
Table 6 Devices data window fields	35
Displaying detailed device information	35
Figure 14 Detailed Devices Display dialog box	35
Managing device port nicknames	35
Creating a nickname	36
Editing a nickname	36
Deleting a nickname	36
Exporting nicknames to a file	36
Importing a nicknames file	37
Zoning	37
Active Zoneset data window	37
Figure 15 Active Zoneset data window	37
Configured Zonesets data window	38
Figure 16 Configured Zoneset data window	38
Zoning concepts	38
Zones	38
Aliases	39
Zonesets	39
Zoning database	39
Viewing zoning limits and properties	39
Managing the zoning database	40
Editing the zoning database	40
Figure 17 Edit Zoning dialog box	40
Table 7 Edit Zoning dialog box tool bar	42
Table 8 Port/Device icons	42
Options for resolving zoning	43
Configuring the zoning database	43
Figure 18 Zoning Config dialog box	43
Merge Auto Save	43
Default Zone	44
Discard Inactive	44
Saving and restoring the zoning database to a file	44
Saving the zoning database to a file	44
Restoring the zoning database from a file	44
Restoring the default zoning database	44
Removing all zone and zoneset definitions	45
Managing zonesets	45
Creating a zoneset	45
Activating and deactivating a zoneset	45
Renaming a zoneset	46
Removing a zoneset	46
Managing zones	46
Creating a zone in a zoneset	46
Copying a zone to a zoneset	47
Adding zone members	47
Renaming a zone	47
Removing a zone member	48
Removing a zone from a zoneset	48
Removing a zone from all zonesets	48
Managing aliases	48
Creating an alias	48
Adding a member to an alias	49
Removing an alias from all zones	49
Merging fabrics and zoning	49
Zone merge failure	49
Zone merge failure recovery	50
Managing switches	51
Switch data window	51
Figure 19 Switch data window	51
Switch data window buttons	52
Figure 20 Switch data window buttons	52
Table 9 Switch data window fields	52
Stack Links data window	56
Figure 21 Stack Links data window	56
Table 10 Stack Links data window	56
Managing Switch Stacks	56
Security Consistency Checklist	57
Figure 22 Security Consistency Checklist dialog box	58
Managing user accounts	58
Creating user accounts	59
Figure 23 User Account Administration–Add Account dialog box	59
Removing a user account	59
Figure 24 User Account Administration–Remove Account dialog box	60
Changing a user account password	60
Figure 25 User Account Administration–Change Password dialog box	60
Modifying a user account	61
Figure 26 User Account Administration–Modify Account dialog box	61
Paging a switch	61
Setting the date/time and enabling NTP client	61
Figure 27 Date/Time dialog box	62
Resetting a switch	62
Table 11 Switch resets	63
Configuring a switch	63
Using the configuration wizard	63
Switch properties	64
Figure 28 Switch Properties dialog box	64
Domain ID and Domain ID Lock	64
Syslog	64
Symbolic name	65
Switch administrative states	65
Broadcast support	65
In-band management	65
Fabric device management interface	65
Advanced switch properties	66
Figure 29 Advanced Switch Properties dialog box	66
Timeout values	66
Managing system services	66
Figure 30 System Services dialog box	67
Network properties	68
Figure 31 Network Properties dialog boxes	68
Network IP configuration	69
IPv4 and IPv6 addressing	69
Table 12 Network Properties dialog box—IP fields	69
Network DNS configuration	71
Table 13 Network Properties dialog box—DNS fields	71
SNMP configuration	72
SNMP properties and trap configuration parameters	72
Figure 32 SNMP Properties dialog box	72
Table 14 SNMP Properties dialog box fields	72
SNMP v3 Security	73
Figure 33 SNMP v3 Manager dialog box	74
Figure 34 SNMP v3 User Editor dialog box	75
Table 15 SNMP v3 User Editor dialog box fields	75
Testing a switch	75
Figure 35 Switch Diagnostics dialog box	76
Archiving a switch	77
Restoring a switch	77
Figure 36 Restore dialog boxes—full and selective	78
Restoring the factory default configuration	79
Table 16 Factory default configuration settings	79
Installing feature license keys	80
Figure 37 Feature Licenses dialog box	80
Figure 38 Add License Key dialog box	81
Downloading a support file	81
Installing firmware	81
Figure 39 Load Firmware dialog box	82
Using Call Home	82
Figure 40 Call Home Setup dialog box	83
Table 17 Call Home Setup fields	84
Using the Call Home Profile Manager	86
Figure 41 Call Home Profile Manager dialog box	86
Using the Call Home Profile Editor	86
Figure 42 Call Home Profile Editor dialog box	87
Using the Call Home Profile Editor—Tech Support Center Profile dialog box	88
Figure 43 Call Home Profile Editor—Tech Support Center Profile dialog box	88
Table 18 Call Home Editor—Tech Support Center Profile dialog box fields	89
Applying all profiles on a switch to other switches	90
Figure 44 Call Home Profile Multiple Switch Apply dialog box	90
Using the Call Home Message Queue	91
Figure 45 Call Home Message Queue dialog box	91
Testing Call Home Profiles	91
Figure 46 Call Home Test Profile dialog box	91
Change Over	92
Figure 47 Call Home Change Over dialog box	92
Managing ports	93
Port Information data window	93
Figure 48 Port Information data window	93
Figure 49 Port Information data window buttons	93
Table 19 Port Information data window fields	94
Port Statistics data window	96
Figure 50 Port Statistics data window	96
Table 20 Port Statistics data window fields	96
Viewing and configuring ports	99
Figure 51 Port Properties dialog box	99
Table 21 Port Properties dialog box fields	99
Port symbolic name	100
Port states	100
Port operational states	101
Table 22 Port operational states	101
Port administrative states	101
Table 23 Port administrative states	101
Port types	102
Table 24 Port types	102
Port speeds	102
Table 25 Port speeds	103
Port transceiver media status	104
Table 26 Port transceiver media view	104
I/O Stream Guard	104
Device Scan	104
Auto Performance Tuning and AL Fairness	105
Figure 52 Advanced Port Properties dialog box	105
Resetting a port	105
Testing ports	105
Figure 53 Port Diagnostics dialog box	106
Glossary	107
Index	111
A	111
B	111
C	111
D	111
E	111
F	111
G	111
H	111
I	111
M	111
N	111
O	111
P	112
R	112
S	112
T	112
U	112
W	112
X	112

Match case Limit results 1 per page

HP StorageWorks SN6000 Fibre Channel Switch QuickTools Switch Management User Guide

Operational State

Switch operational state: Online, Offline, Diagnostic, Down

Administrative State

Current switch administrative state

Configured Admin State

Administrative state that is stored in the switch configuration

Beacon Status

Beacon status. Switch LEDs are blinking (On) or not blinking

(Off).

Reason for Status

The reason for the operational state.

Temperature

Internal switch temperature °C

Power Supply 1 Status

Whether the switch is On or Off

Temperature Failure Port

Shutdown

Non-configurable (always enabled for this switch). All ports

are shut down when the switch temperature exceeds the

Failure Temperature.

Warning Temperature

Non-configurable temperature threshold (65° C), above

which a warning condition alarm is generated.

Failure Temperature

Non-configurable temperature threshold (70° C), above

which a failure condition alarm is generated.

POST Status

The current diagnostic state of the switch.

POST Fault Code

The code value for the last recorded diagnostic test result

recorded on the switch.

Test Status

The current diagnostic test status of switch.

Test Fault Code

The code value for the last recorded diagnostic test status

recorded on the switch.

Network Group

IPv4 Enabled

Internet Protocol version 4 Enabled or Disabled

IPv4 Address

Internet Protocol version 4 address

IPv4 Subnet Mask

Mask that determines the IP address subnet

IPv4 Gateway

Gateway address

IPv6 Enabled

Internet Protocol version 6 Enabled or Disabled

IPv6 Address

Mask that determines the IP address subnet

IPv6 Gateway

Gateway address

SNMP Enabled

SNMP Enabled or Disabled

SNMP v3 Security Enabled

SNMP v3 Security Enabled or Disabled

Broadcast Support

Broadcast support status. Broadcast support is enabled

(default) or disabled.

NTP Client Enabled

NTP Client Enabled or Disabled. If Enabled, this parameter

enables switches to synchronize their time to a centralized

server.

NTP Server Address

The IP address of the centralized NTP server. Ethernet

connection to NTP server is required.

DNS Enabled

Domain Name Service Enabled or Disabled

Table 9

Switch data window fields

Field

Description