Home » HP Manuals » Storage Devices » HP StorageWorks SN6000 » Manual Viewer

HP StorageWorks SN6000 HP StorageWorks SN6000 QuickTools Switch management use - Page 57

Security Consistency Checklist, Stack, Move Switch Up, Remove Switch, Remove Links

View all HP StorageWorks SN6000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

The graphic window (upper right pane of the faceplate display) displays one faceplate image for each switch in the stack. In the fabric tree (left window pane), the switches in each stack are nested under the stack icon, which is nested under the fabric icon. Expanding the fabric and stack icons in the fabric tree displays all switches in a stack. The lock image on the fabric icon indicates that the application is communicating with the fabric through a secure (Secure Sockets Layer) connection. The stack dialogs are essentially the same as their corresponding switch dialogs, except that the Select Switch for Initial Configuration pull-down menu is added to each dialog. The stack dialogs display the information for the switch selected in the Select Switch for Initial Configuration pull-down menu. Choose another switch in the pull-down menu to display information for that switch. After you click OK, the switch configuration that was displayed is the configuration that is applied to all other switches in the stack. The following operations are available to configure the stack as a single entity: • Date/time and NTP settings. For more information, see "Setting the date/time and enabling NTP client" on page 61. • Firmware load and activation. For more information, see "Installing firmware" on page 81. • Switch reset. For more information, see "Resetting a switch" on page 62. • Editing user accounts. For more information, see ""Managing user accounts" on page 58. • SNMP configuration. For more information, see "SNMP configuration" on page 72. • Security Consistency Checklist. For more information, see "Security Consistency Checklist" on page 57. • Syslog configuration. For more information, see "Syslog" on page 64. Additional stack operations include the following: • Move the selected switch up or down one position in the stack within the graphic window. To move a switch image up, select a switch, open the Stack menu, and select Move Switch Up. To move a switch image down, select a switch, open the Stack menu, and select Move Switch Down. • Remove a switch from being associated with the stack if the switch is not connected to any other switch in the fabric with an ISL connection. To remove a switch from a stack, select a switch, open the Stack menu, and select Remove Switch. • Remove a dead ISL connection in the stack display between two switches that is either offline or has been physically disconnected. To remove a dead link (red), select one of the linked XPAK ports, open the Stack menu, and select Remove Links. • Refresh the stack to update the faceplate display with current information for all switches in the stack • Select all ports on all switches in the stack. Security Consistency Checklist The Security Consistency Checklist dialog box (Figure 22) enables you to view current security-related settings, such as, firmware versions, embedded GUI, in-band management, date/time on switches. Any changes must be made through the appropriate dialog, such as Network Properties dialog, Switch HP StorageWorks SN6000 Fibre Channel Switch QuickTools Switch Management User Guide 57

Section	Page
Contents	3
About this guide	9
Intended audience	9
Prerequisites	9
Related documentation	9
Document conventions and symbols	10
Table 1 Document conventions	10
JDOM license	10
HP technical support	11
Subscription service	11
HP-authorized reseller	11
Helpful websites	12
Using QuickTools	13
Workstation requirements	13
Table 2 Workstation requirements	13
Opening QuickTools	13
Figure 1 Add a New Fabric dialog box	14
Figure 2 Password Change Required dialog box	14
QuickTools user interface	14
Figure 3 QuickTools interface	15
Fabric tree	15
Graphic window	15
Data windows and tabs	15
Alerts panel	16
Figure 4 Alerts panel	16
Menu bar	17
Table 3 Menu bar options	17
Popup menus	19
Shortcut keys	19
Selecting switches	19
Selecting ports	19
Setting QuickTools preferences	19
Figure 5 Preferences dialog box–QuickTools	20
Using online Help	20
Viewing the software version	20
Exiting QuickTools	21
Managing fabrics	23
Fabric services	23
Enabling SNMP configuration	23
Enabling in-band management	23
Rediscovering a fabric	23
Adding a new switch to a fabric	23
Replacing a failed switch	24
Transparent Router	24
TR Mapping Manager dialog	26
Figure 6 TR Mapping Manager dialog	26
Removing an inter-fabric route	26
Add TR Mapping dialog	27
Figure 7 Add TR Mapping dialog	27
Mapping a new inter-fabric zone	27
Remote Fabric Zoning dialog	28
Figure 8 Remote Fabric Zoning dialog	28
Transparent Routes data window	30
Figure 9 Transparent Routes data window	30
Table 4 Transparent Routes data window fields	30
Figure 10 Transparent Route dialog	31
Event Browser	31
Figure 11 Event Browser dialog box	32
Table 5 Port operational states	32
Filtering the Event Browser	33
Figure 12 Filter Events dialog box	33
Sorting the Event Browser	33
Saving the Event Browser to a file	34
Device information and nicknames	34
Devices data window	34
Figure 13 Devices data window	34
Table 6 Devices data window fields	35
Displaying detailed device information	35
Figure 14 Detailed Devices Display dialog box	35
Managing device port nicknames	35
Creating a nickname	36
Editing a nickname	36
Deleting a nickname	36
Exporting nicknames to a file	36
Importing a nicknames file	37
Zoning	37
Active Zoneset data window	37
Figure 15 Active Zoneset data window	37
Configured Zonesets data window	38
Figure 16 Configured Zoneset data window	38
Zoning concepts	38
Zones	38
Aliases	39
Zonesets	39
Zoning database	39
Viewing zoning limits and properties	39
Managing the zoning database	40
Editing the zoning database	40
Figure 17 Edit Zoning dialog box	40
Table 7 Edit Zoning dialog box tool bar	42
Table 8 Port/Device icons	42
Options for resolving zoning	43
Configuring the zoning database	43
Figure 18 Zoning Config dialog box	43
Merge Auto Save	43
Default Zone	44
Discard Inactive	44
Saving and restoring the zoning database to a file	44
Saving the zoning database to a file	44
Restoring the zoning database from a file	44
Restoring the default zoning database	44
Removing all zone and zoneset definitions	45
Managing zonesets	45
Creating a zoneset	45
Activating and deactivating a zoneset	45
Renaming a zoneset	46
Removing a zoneset	46
Managing zones	46
Creating a zone in a zoneset	46
Copying a zone to a zoneset	47
Adding zone members	47
Renaming a zone	47
Removing a zone member	48
Removing a zone from a zoneset	48
Removing a zone from all zonesets	48
Managing aliases	48
Creating an alias	48
Adding a member to an alias	49
Removing an alias from all zones	49
Merging fabrics and zoning	49
Zone merge failure	49
Zone merge failure recovery	50
Managing switches	51
Switch data window	51
Figure 19 Switch data window	51
Switch data window buttons	52
Figure 20 Switch data window buttons	52
Table 9 Switch data window fields	52
Stack Links data window	56
Figure 21 Stack Links data window	56
Table 10 Stack Links data window	56
Managing Switch Stacks	56
Security Consistency Checklist	57
Figure 22 Security Consistency Checklist dialog box	58
Managing user accounts	58
Creating user accounts	59
Figure 23 User Account Administration–Add Account dialog box	59
Removing a user account	59
Figure 24 User Account Administration–Remove Account dialog box	60
Changing a user account password	60
Figure 25 User Account Administration–Change Password dialog box	60
Modifying a user account	61
Figure 26 User Account Administration–Modify Account dialog box	61
Paging a switch	61
Setting the date/time and enabling NTP client	61
Figure 27 Date/Time dialog box	62
Resetting a switch	62
Table 11 Switch resets	63
Configuring a switch	63
Using the configuration wizard	63
Switch properties	64
Figure 28 Switch Properties dialog box	64
Domain ID and Domain ID Lock	64
Syslog	64
Symbolic name	65
Switch administrative states	65
Broadcast support	65
In-band management	65
Fabric device management interface	65
Advanced switch properties	66
Figure 29 Advanced Switch Properties dialog box	66
Timeout values	66
Managing system services	66
Figure 30 System Services dialog box	67
Network properties	68
Figure 31 Network Properties dialog boxes	68
Network IP configuration	69
IPv4 and IPv6 addressing	69
Table 12 Network Properties dialog box—IP fields	69
Network DNS configuration	71
Table 13 Network Properties dialog box—DNS fields	71
SNMP configuration	72
SNMP properties and trap configuration parameters	72
Figure 32 SNMP Properties dialog box	72
Table 14 SNMP Properties dialog box fields	72
SNMP v3 Security	73
Figure 33 SNMP v3 Manager dialog box	74
Figure 34 SNMP v3 User Editor dialog box	75
Table 15 SNMP v3 User Editor dialog box fields	75
Testing a switch	75
Figure 35 Switch Diagnostics dialog box	76
Archiving a switch	77
Restoring a switch	77
Figure 36 Restore dialog boxes—full and selective	78
Restoring the factory default configuration	79
Table 16 Factory default configuration settings	79
Installing feature license keys	80
Figure 37 Feature Licenses dialog box	80
Figure 38 Add License Key dialog box	81
Downloading a support file	81
Installing firmware	81
Figure 39 Load Firmware dialog box	82
Using Call Home	82
Figure 40 Call Home Setup dialog box	83
Table 17 Call Home Setup fields	84
Using the Call Home Profile Manager	86
Figure 41 Call Home Profile Manager dialog box	86
Using the Call Home Profile Editor	86
Figure 42 Call Home Profile Editor dialog box	87
Using the Call Home Profile Editor—Tech Support Center Profile dialog box	88
Figure 43 Call Home Profile Editor—Tech Support Center Profile dialog box	88
Table 18 Call Home Editor—Tech Support Center Profile dialog box fields	89
Applying all profiles on a switch to other switches	90
Figure 44 Call Home Profile Multiple Switch Apply dialog box	90
Using the Call Home Message Queue	91
Figure 45 Call Home Message Queue dialog box	91
Testing Call Home Profiles	91
Figure 46 Call Home Test Profile dialog box	91
Change Over	92
Figure 47 Call Home Change Over dialog box	92
Managing ports	93
Port Information data window	93
Figure 48 Port Information data window	93
Figure 49 Port Information data window buttons	93
Table 19 Port Information data window fields	94
Port Statistics data window	96
Figure 50 Port Statistics data window	96
Table 20 Port Statistics data window fields	96
Viewing and configuring ports	99
Figure 51 Port Properties dialog box	99
Table 21 Port Properties dialog box fields	99
Port symbolic name	100
Port states	100
Port operational states	101
Table 22 Port operational states	101
Port administrative states	101
Table 23 Port administrative states	101
Port types	102
Table 24 Port types	102
Port speeds	102
Table 25 Port speeds	103
Port transceiver media status	104
Table 26 Port transceiver media view	104
I/O Stream Guard	104
Device Scan	104
Auto Performance Tuning and AL Fairness	105
Figure 52 Advanced Port Properties dialog box	105
Resetting a port	105
Testing ports	105
Figure 53 Port Diagnostics dialog box	106
Glossary	107
Index	111
A	111
B	111
C	111
D	111
E	111
F	111
G	111
H	111
I	111
M	111
N	111
O	111
P	112
R	112
S	112
T	112
U	112
W	112
X	112

Match case Limit results 1 per page

HP StorageWorks SN6000 Fibre Channel Switch QuickTools Switch Management User Guide

The graphic window (upper right pane of the faceplate display) displays one faceplate image for each

switch in the stack.

In the fabric tree (left window pane), the switches in each stack are nested under the stack icon, which is

nested under the fabric icon. Expanding the fabric and stack icons in the fabric tree displays all switches in

a stack. The lock image on the fabric icon indicates that the application is communicating with the fabric

through a secure (Secure Sockets Layer) connection.

The stack dialogs are essentially the same as their corresponding switch dialogs, except that the Select

Switch for Initial Configuration pull-down menu is added to each dialog. The stack dialogs display the

information for the switch selected in the Select Switch for Initial Configuration pull-down menu. Choose

another switch in the pull-down menu to display information for that switch. After you click

, the switch

configuration that was displayed is the configuration that is applied to all other switches in the stack. The

following operations are available to configure the stack as a single entity:

•

Date/time and NTP settings. For more information, see ”

Setting the date/time and enabling NTP

client

” on page 61.

•

Firmware load and activation. For more information, see ”

Installing firmware

” on page 81.

•

Switch reset. For more information, see ”

Resetting a switch

” on page 62.

•

Editing user accounts. For more information, see “”

Managing user accounts

” on page 58.

•

SNMP configuration. For more information, see ”

SNMP configuration

” on page 72.

•

Security Consistency Checklist. For more information, see ”

Security Consistency Checklist

” on page 57.

•

Syslog configuration. For more information, see ”

Syslog

” on page 64.

Additional stack operations include the following:

•

Move the selected switch up or down one position in the stack within the graphic window. To move a

switch image up, select a switch, open the

Stack

menu, and select

Move Switch Up

. To move a switch

image down, select a switch, open the

Stack

menu, and select

Move Switch Down

•

Remove a switch from being associated with the stack if the switch is not connected to any other switch

in the fabric with an ISL connection. To remove a switch from a stack, select a switch, open the

Stack

menu, and select

Remove Switch

•

Remove a dead ISL connection in the stack display between two switches that is either offline or has

been physically disconnected. To remove a dead link (red), select one of the linked XPAK ports, open

the

Stack

menu, and select

Remove Links

•

Refresh the stack to update the faceplate display with current information for all switches in the stack

•

Select all ports on all switches in the stack.

Security Consistency Checklist

The Security Consistency Checklist dialog box (

Figure 22

) enables you to view current security-related

settings, such as, firmware versions, embedded GUI, in-band management, date/time on switches. Any

changes must be made through the appropriate dialog, such as Network Properties dialog, Switch