HP Surestore Tape Library Model 2/28 HP DLT Tape Library 28/48-Slot - User& - Page 80

Running an Internal Test, ADMIN, NUM LOOPS 1, TEST CANCEL - WAIT

Get HP Surestore Tape Library Model 2/28 PDF manuals and user guides View all HP Surestore Tape Library Model 2/28 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Library Operation Running an Internal Test CAUTION NOTE NOTE Running an Internal Test Some diagnostic tests, such as Exchange Demo, may place tape cartridges in unexpected locations, which can cause problems with the software application being used. Some diagnostic tests can only be run through the SCSI interface. Refer to Digital Linear Tape Drive and Library SCSI-2 Command Reference (HP part number 5960-7674) for information about these tests. To run self-diagnostic tests: 1. Verify that the drive status displays (if not, press CANCEL until it does). 2. Press NEXT until ADMIN* appears in the display window, then press ENTER. 3. Enter the three-part numerical password (see "Entering the Administration Menu Password" on page 3-7). 4. INFO* displays. Press NEXT or PREV until TEST* displays, then press ENTER. 5. Press NEXT until the name of the test to run displays, then press ENTER. 6. NUM LOOPS 1 displays, where the 1 is flashing. Press NEXT until the number of test loops you wish to run displays, then press ENTER. Press CANCEL at any time to abort a test. TEST CANCEL - WAIT displays while the current test loop completes. The following table describes the internal tests available from the control panel. Tests are listed alphabetically according to function. 4-36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
4-36
Library Operation
Running an Internal Test
Running an Internal Test
CAUTION
Some diagnostic tests, such as Exchange Demo, may place tape cartridges in
unexpected locations, which can cause problems with the software
application being used.
NOTE
Some diagnostic tests can only be run through the SCSI interface. Refer to
Digital Linear Tape Drive and Library SCSI-2 Command Reference
(HP
part number 5960-7674) for information about these tests.
To run self-diagnostic tests:
1.
Verify that the drive status displays (if not, press
CANCEL
until it does).
2.
Press
NEXT
until
ADMIN*
appears in the display window, then press
ENTER
.
3.
Enter the three-part numerical password (see “Entering the
Administration Menu Password” on page 3-7).
4.
INFO*
displays. Press
NEXT
or
PREV
until
TEST*
displays, then press
ENTER
.
5.
Press
NEXT
until the name of the test to run displays, then press
ENTER
.
6.
NUM LOOPS 1
displays, where the 1 is flashing. Press
NEXT
until the
number of test loops you wish to run displays, then press
ENTER
.
NOTE
Press
CANCEL
at any time to abort a test.
TEST CANCEL - WAIT
displays
while the current test loop completes.
The following table describes the internal tests available from the control
panel. Tests are listed alphabetically according to function.