HP Vectra VE 5/xxx HP Vectra VE5/xx Series 2 PC - User’s Guide, D4000 - Page 35

Connect the data and power cables to the rear of the device installed in the middle shelf.

Get HP Vectra VE 5/xxx - 2 PDF manuals and user guides View all HP Vectra VE 5/xxx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

5 Connect the data and power cables to the rear of the device installed in the middle shelf. The connectors are shaped to go in one way only. If you are installing an IDE CD-ROM drive, connect the drive to the CD-ROM data cable. This data cable should be connected to the connector marked "CD-ROM" on the system board. If you are not sure which connector to use, refer to "Connecting IDE Devices" earlier in this chapter. 6 Install any other accessories before replacing the cover. Reconnect all cables and power cords. WARNING: Do not open the CD-ROM drive enclosure as there is a danger of electric shock, and the laser beam light could harm your eyes. Service should be carried out by qualified personnel. This PC is a class 1 laser product. To avoid discomfort from unexpected noise, always turn the volume down before connecting headphones or speakers. Listening to loud sounds for prolonged periods may permanently damage your hearing. Before putting on headphones, place them round your neck and turn the volume down. When you put on the headphones, slowly increase the volume until you find a comfortable listening level and leave the volume control in that position.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
5
Connect the data and power cables to the rear of the device installed in the middle shelf.
The connectors are shaped to go in one way only. If you are installing an IDE CD-ROM
drive, connect the drive to the CD-ROM data cable. This data cable should be connected
to the connector marked “CD-ROM” on the system board. If you are not sure which
connector to use, refer to "Connecting IDE Devices" earlier in this chapter.
6
Install any other accessories before replacing the cover. Reconnect all cables and power
cords.
WARNING:
Do not open the CD-ROM drive enclosure as
there is a danger of electric shock, and the laser
beam light could harm your eyes. Service should
be carried out by qualified personnel.
This PC is a class 1 laser product. To avoid
discomfort from unexpected noise, always turn
the volume down before connecting headphones
or speakers. Listening to loud sounds for
prolonged periods may permanently damage
your hearing.
Before putting on headphones, place them round
your neck and turn the volume down. When you
put on the headphones, slowly increase the
volume until you find a comfortable listening
level and leave the volume control in that
position.