HP dx6050 Troubleshooting Guide - Page 46

Advanced, Network, Control Panel, Problem, Cause, Solution, Under the Computer Setup

Page 46 highlights

Troubleshooting Without Diagnostics Solving Network Problems (Continued) Problem Cause Diagnostics reports a failure. (continued) There is a problem with the cable or a device at the other end of the cable. Network controller interrupt is shared with an expansion board. The network controller is defective. Diagnostics passes, but the computer does not communicate with the network. Network drivers are not loaded, or driver parameters do not match current configuration. Network controller stopped working when an expansion board was added to the computer. The network controller is not configured for this computer. Network controller interrupt is shared with an expansion board. The network controller requires drivers. The expansion board installed is a network card (NIC) and conflicts with the embedded NIC. Solution Ensure that the cable and device at the other end are operating correctly. Under the Computer Setup Advanced menu, change the resource settings for the board. Contact an authorized service provider. Make sure the network drivers are loaded and that the driver parameters match the configuration of the network controller. Make sure the correct network client and protocol is installed. Select the Network icon in the Control Panel and configure the network controller. Under the Computer Setup Advanced menu, change the resource settings for the board. Verify that the drivers were not accidentally deleted when the drivers for a new expansion board were installed. Under the Computer Setup Advanced menu, change the resource settings for the board. 2-30 www.hp.com Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85

2–30
www.hp.com
Troubleshooting Guide
Troubleshooting Without Diagnostics
Diagnostics reports a
failure.
(continued)
There is a problem with
the cable or a device at
the other end of the cable.
Ensure that the cable and device at
the other end are operating
correctly.
Network controller
interrupt is shared with
an expansion board.
Under the Computer Setup
Advanced
menu, change the
resource settings for the board.
The network controller
is defective.
Contact an authorized service
provider.
Diagnostics passes, but
the computer does not
communicate with the
network.
Network drivers are
not loaded, or driver
parameters do not match
current configuration.
Make sure the network drivers
are loaded and that the driver
parameters match the configuration
of the network controller.
Make sure the correct network client
and protocol is installed.
The network controller
is not configured for this
computer.
Select the
Network
icon in the
Control Panel
and configure the
network controller.
Network controller
stopped working when
an expansion board was
added to the computer.
Network controller
interrupt is shared with an
expansion board.
Under the Computer Setup
Advanced
menu, change the
resource settings for the board.
The network controller
requires drivers.
Verify that the drivers were not
accidentally deleted when the
drivers for a new expansion board
were installed.
The expansion board
installed is a network card
(NIC) and conflicts with
the embedded NIC.
Under the Computer Setup
Advanced
menu, change the
resource settings for the board.
Solving Network Problems
(Continued)
Problem
Cause
Solution