HP vp6300 HP vp6300 Series Digital Projector - User's Guide - Page 57

Power and status functions, Setup functions continued

Get HP vp6300 - Digital Projector PDF manuals and user guides View all HP vp6300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Setup functions (continued) Command Parameters THRS ? POS 0 to 3, ? TMO PTMO 5 to 20, ? 0, 3 to 6, ? VERS ? SNUM ? Description Queries the total time (in tenths of hours) that the projector has been in use. Sets or queries the projector's position: 0=front table, 1=front ceiling, 2=rear table, 3=rear ceiling. Sets or queries the menu timeout setting (seconds) Sets or queries the power timeout: 0=never, 3=15 min, 4=30 min, 5=60 min, 6=120 min. Queries the projector model number and firmware version. The notification takes this form: *VERS="proj_model:proj_fw" Queries the projector's serial number. Power and status functions Command Parameters SHDN None W or WAKE None Description Puts the projector into cool-down state, and later into standby state. The projector sends a notification when it enters cooldown state (STAT=3), and another when it enters standby state (STAT=0). This keyword requires the projector to be in its on state (STAT=1). Do not send any requests other than STAT in the time between the cool-down and standby state notifications. Otherwise, unexpected results can occur. Puts the projector into warm-up state, and later into on state. The projector sends a notification when it enters warm-up state (STAT=2), and another when it enters the on state (STAT=1). This keyword requires the projector to be in standby state (STAT=0). Do not send any requests other than STAT in the time between the warm-up and on state notifications. Otherwise, unexpected results can occur. Connecting to a room controller 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Connecting to a room controller
57
THRS
?
Queries the total time (in tenths of hours) that the projector has
been in use.
POS
0 to 3, ?
Sets or queries the projector’s position: 0=front table, 1=front
ceiling, 2=rear table, 3=rear ceiling.
TMO
5 to 20, ?
Sets or queries the menu timeout setting (seconds)
PTMO
0, 3 to 6, ?
Sets or queries the power timeout: 0=never, 3=15 min, 4=30
min, 5=60 min, 6=120 min.
VERS
?
Queries the projector model number and firmware version. The
notification takes this form:
*VERS=”proj_model:proj_fw”
SNUM
?
Queries the projector's serial number.
Power and status functions
Command
Parameters
Description
SHDN
None
Puts the projector into cool-down state, and later into standby
state. The projector sends a notification when it enters cool-
down state (STAT=3), and another when it enters standby state
(STAT=0). This keyword requires the projector to be in its on
state (STAT=1).
Do not send any requests other than STAT in the time between
the cool-down and standby state notifications. Otherwise,
unexpected results can occur.
W or WAKE
None
Puts the projector into warm-up state, and later into on state.
The projector sends a notification when it enters warm-up state
(STAT=2), and another when it enters the on state (STAT=1).
This keyword requires the projector to be in standby state
(STAT=0).
Do not send any requests other than STAT in the time between
the warm-up and on state notifications. Otherwise, unexpected
results can occur.
Setup functions (continued)
Command
Parameters
Description