Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm User Manual - Page 102

Report Face Modeling Information in Multi-Target-Type Capture Alarm

Get Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm PDF manuals and user guides View all Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual Face Modeling Face modeling serves the purpose of collecting face pictures, creating face models, and uploading data to the surveillance center. Before You Start Face Capture or Multi-Target-Type detection should be configured for face picture collection. See Face Capture or Multi-Target-Type Detection for configuration instructions. Steps 1. Go to Configuration → Comparison and Modeling → Face Comparison and Modeling. 2. Select Face Modeling to start. 3. Check Enable Face Modeling. 4. Set parameters for modeling. • Report Face Modeling Information in Multi-Target-Type Capture Alarm: When a person triggers the multi-target-type detection, the alarm information includes the face modeling information of the detected face if checked. • Quick Capture: The device starts face modeling when it detects a face that scores higher than the set face grading threshold for capture. • Face Grading Threshold for Capture: The face grading threshold for the device to judge whether to capture and upload the face or not. Higher value means better picture quality. • Max. Capture Interval: The max. interval between two captures when the target is in the detection area. The camera takes the capture when it reaches the max. interval even if the face grading does not reach the set threshold. 5. Set arming schedule. See Set Arming Schedule. 6. Set linkage method. See Linkage Method Settings. UM iDS-2CD7xxG0-xxxxx 021021NA 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual
UM iDS-2CD7xxG0-xxxxx 021021NA
102
Face Modeling
Face modeling serves the purpose of collecting face pictures, creating face models, and uploading data
to the surveillance center.
Before You Start
Face Capture or Multi-Target-Type detection should be configured for face picture collection. See
Face
Capture
or
Multi-Target-Type Detection
for configuration instructions.
Steps
1.
Go to
Configuration
→
Comparison and Modeling
→
Face Comparison and Modeling
.
2.
Select
Face Modeling
to start.
3.
Check
Enable Face Modeling
.
4.
Set parameters for modeling.
•
Report Face Modeling Information in Multi-Target-Type Capture Alarm:
When a person triggers the
multi-target-type detection, the alarm information includes the face modeling information of the
detected face if checked.
•
Quick Capture:
The device starts face modeling when it detects a face that scores higher than the
set face grading threshold for capture.
•
Face Grading Threshold for Capture:
The face grading threshold for the device to judge whether to
capture and upload the face or not. Higher value means better picture quality.
•
Max. Capture Interval:
The max. interval between two captures when the target is in the detection
area. The camera takes the capture when it reaches the max. interval even if the face grading does
not reach the set threshold.
5.
Set arming schedule. See
Set Arming Schedule
.
6.
Set linkage method. See
Linkage Method Settings
.