Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm User Manual - Page 49

Set Region Exiting Detection

Get Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm PDF manuals and user guides View all Hikvision IDS-2CD7AC5G0-IZHSY 2.8-12mm manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual 8. Click Save. Set Region Entrance Detection Use to detect objects entering a pre-defined virtual region. If it occurs, the device can take linkage actions. Steps 1. Go to Configuration → Event → Smart Event → Region Entrance Detection. 2. Check Enable. 3. Select one Region. For the region settings, refer to Draw Area. 4. Select the detection target. Human and Vehicle are available. If the detection target is not selected, all detected targets will be reported, including humans and vehicles. Figure 6-6 Set Rule 5. Optional: You can set the parameters of multiple areas by repeating the above steps. 6. For the arming schedule settings, refer to Set Arming Schedule. For the linkage method settings, refer to Linkage Method Settings. 7. Click Save. Set Region Exiting Detection Detects objects exiting from a pre-defined virtual region. If it occurs, the device can take linkage actions. Steps 1. Go to Configuration → Event → Smart Event → Region Exiting Detection. 2. Check Enable. 3. Select one Region. For the detection region settings, refer to Draw Area. UM iDS-2CD7xxG0-xxxxx 021021NA 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
iDS-2CD7xxG0-xxxxx Network Bullet Camera User Manual
UM iDS-2CD7xxG0-xxxxx 021021NA
49
8.
Click
Save
.
Set Region Entrance Detection
Use to detect objects entering a pre-defined virtual region. If it occurs, the device can take linkage
actions.
Steps
1.
Go to
Configuration
→
Event
→
Smart Event
→
Region Entrance Detection
.
2.
Check
Enable
.
3.
Select one
Region
. For the region settings, refer to
Draw Area
.
4.
Select the detection target.
Human
and
Vehicle
are available. If the detection target is not selected, all
detected targets will be reported, including humans and vehicles.
Figure 6-6 Set Rule
5.
Optional: You can set the parameters of multiple areas by repeating the above steps.
6.
For the arming schedule settings, refer to
Set Arming Schedule
. For the linkage method settings, refer
to
Linkage Method Settings
.
7.
Click
Save
.
Set Region Exiting Detection
Detects objects exiting from a pre-defined virtual region. If it occurs, the device can take linkage actions.
Steps
1.
Go to
Configuration
→
Event
→
Smart Event
→
Region Exiting Detection
.
2.
Check
Enable
.
3.
Select one
Region
. For the detection region settings, refer to
Draw Area
.