Hitachi 55DMX01W Owners Guide - Page 82

Warning, Caution

Get Hitachi 55DMX01W PDF manuals and user guides View all Hitachi 55DMX01W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

DEMAN MOI! LAMP REPLACEMENT 3. Loosen the two screws securing the latch cover with a Phillips Head Screw Driver as shown. If these screws are not loosened completely, the lamp unit cannot be removed. ✬ ☞✍ ✬ ✲ ☞✍ 8Ω ONLY STOP CONNECT ONLY 8 OHM SPEAKERS DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty) ✹ ✹ ✰✢ ✲ ✣✲ ✬ 54321 10 9 8 7 6 15 14 13 12 11 ANTA ✡✮✴✢ Lamp Unit Retaining Screws CAUTION: THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS. AFTER UNPLUGGING THE POWER CORD, WAIT AT LEAST 30 MINUTES UNTIL THE LAMP IS COOL BEFORE ATTEMPTING TO REMOVE. 4. Remove the lamp unit by holding the lamp handle, then pulling outwards. Exercise caution when removing the lamp unit to avoid injury to your fingers. If the lamp unit does not come out easily, check to make sure the screws in step 3 are loosened completely. WARNING: DO NOT PUT YOUR HAND IN THE LAMP STORAGE AREA AFTER THE LAMP UNIT IS REMOVED, YOU MAY GET BURNED. SUB WOOFER L R AUDIO TO HI-FI + - L R + - REAR SPEAKER 8Ω ONLY STOP CONNECT ONLY 8 OHM SPEAKERS DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty) COAXIAL OPTICAL INPUT INPUT S-VIDEO S-VIDEO S-VIDEO VIDEO Y VIDEO Y (MONO) P B L CR R AUDIO INPUT 1 (MONO) L PB CR R AUDIO INPUT 2 VIDEO (MONO) L R AUDIO MONITOR OUT L R PC AUDIO INPUT 1 54321 10 9 8 7 6 15 14 13 12 11 PC RGB INPUT 1 ANT A TO CONVERTER ANT B Handle Lamp Unit 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
82
LAMP REPLACEMENT
3.
Loosen the two screws securing the latch cover with a Phillips Head Screw Driver as
shown.
If these screws are not loosened completely, the lamp unit cannot be removed.
STOP
Lamp Unit Retaining Screws
4.
Remove the lamp unit by holding the lamp handle, then pulling outwards.
Exercise
caution when removing the lamp unit to avoid injury to your fingers.
If the lamp unit does
not come out easily, check to make sure the screws in step 3 are loosened completely.
WARNING:
DO NOT PUT YOUR HAND IN THE LAMP STORAGE AREA AFTER THE LAMP UNIT
IS REMOVED, YOU MAY GET BURNED.
STOP
Handle
Lamp Unit
CAUTION:
THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS.
AFTER
UNPLUGGING THE POWER CORD, WAIT AT LEAST 30 MINUTES UNTIL THE LAMP
IS COOL BEFORE ATTEMPTING TO REMOVE.