Hitachi C52-WD9000 Owners Guide - Page 52

About the jacks and connections of rear panel

Get Hitachi C52-WD9000 PDF manuals and user guides View all Hitachi C52-WD9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

CONNECTION WITH OTHER EQUIPMENT About the jacks and connections of rear panel 1.Refer to the operation manual of your electronic equipment for additional information on connections. 2.If your device has only one audio output (mono sound), please connect it to the left channel jack (L/MONO). 3.Audio and video signal from the same source should be connected to the same group of terminals. Do not mix them. 4.Terminals˄Y/VIDEO,PB/CB,PR/CR˅in INPUT1 and INPUT2 are used to connect component outputs of HDTV STB, DVD, PDVD, etc. Y/VIDEO input terminal can also be used as the standard video terminal. When you use Y/VIDEO, PB/CB, PR/CR terminals to connect component signals, press the RECALL button on the remote control unit to show the characters COMPONENT and AV1 or AV2 on the top right corner of the screen, which indicates that you are using component terminals to receive signals. However, when you use Y/VIDEO terminal instead of Y/VIDEO, PB/CB, PR/CR terminals to receive video signal, only the character AV1 or AV2 will appear on the top right corner of the screen. The HDMI INPUT interface on INPUT1 can be used to connect your external devices equipped with an HDMI output. When the HDMI INPUT interface on INPUT1 is connected, press the RECALL button on the remote control unit to show the characters HDMI or DVI and AV1 on the top right corner of the screen, which indicates that you are viewing the program through the HDMI INPUT interface on INPUT1. Note: 1. When the HDMI INPUT interface on INPUT1 is used, please do not connect terminals (Y/VIDEOˈ PB/CBˈPR/CR) on INPUT1. 2. The C43-FL9000 model does not have HDMI INPUT interface. 5.If your device has s-video signal output, please use s-video signal instead of the standard video signal. If there are signals input from the same group of S-VIDEO and VIDEO terminals, the TV will receive signal from S-VIDEO and the characters S and AV3 or AV4 will appear on the top right corner of the screen by pressing the RECALL button, which indicates that you are using S-VIDEO terminal to receive signals. 6.˄VIDEO˅MONITOR OUT terminal outputs video signal receiving from RF, S-VIDEO or VIDEO terminal to external equipment. When receiving component signals (YˈPB/CBˈPR/CR) or HDMI INPUT interface signal, there is no output from˄VIDEO˅MONITOR OUT terminal. 7.˄S-VIDEO˅MONITOR OUT terminal outputs S-VIDEO signal receiving from S-VIDEIO inputs to external equipment. When receiving signals from RF, VIDEO, Y, PB/CB, PR/CR terminals or HDMI INPUT interface, there is no output from˄S-VIDEO˅MONITOR OUT terminal. 8.˄FIXED/VARIABLE AUDIO˅MONITOR OUT terminals provide fixed or variable audio level output to external stereo system. 9.TV AS CENTER input jacks These jacks are for stereo amplifiers with center signal output capability. This feature allows the TV speakers to be used as a center speaker. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
52
CONNECTION WITH OTHER EQUIPMENT
About the jacks and connections of rear panel
1.Refer to the operation manual of your electronic equipment for additional information on connections.
2.If your device has only one audio output (mono sound), please connect it to the left channel jack (L/MONO).
3.Audio and video signal from the same source should be connected to the same group of terminals. Do not mix
them.
4.Terminals
Y/VIDEO,P
B
/C
B
,P
R
/C
R
in
INPUT1
and
INPUT2
are used to connect component outputs of HDTV
STB, DVD, PDVD, etc. Y/VIDEO input terminal can also be used as the standard video terminal.
When you use Y/VIDEO, P
B
/C
B
, P
R
/C
R
terminals to connect component signals, press the
RECALL
button on
the remote control unit to show the characters
COMPONENT
and
AV1
or
AV2
on the top right corner of the
screen, which indicates that you are using component terminals to receive signals. However, when you use
Y/VIDEO terminal instead of Y/VIDEO, P
B
/C
B
, P
R
/C
R
terminals to receive video signal, only the character
AV1
or
AV2
will appear on the top right corner of the screen.
The HDMI INPUT interface on
INPUT1
can be used to connect your external devices equipped with an HDMI
output. When the HDMI INPUT interface on INPUT1 is connected, press the
RECALL
button on the remote
control unit to show the characters
HDMI
or
DVI
and
AV1
on the top right corner of the screen, which
indicates that you are viewing the program through the HDMI INPUT interface on
INPUT1
.
Note:
1. When the HDMI INPUT interface on
INPUT1
is used, please do not connect terminals (Y/VIDEO
P
B
/C
B
P
R
/C
R
) on
INPUT1
.
2. The C43-FL9000 model does not have HDMI INPUT interface.
5.If your device has s-video signal output, please use s-video signal instead of the standard video signal.
If there are signals input from the same group of S-VIDEO and VIDEO terminals, the TV will receive signal
from S-VIDEO and the characters
S
and
AV3
or
AV4
will appear on the top right corner of the screen by
pressing the
RECALL
button, which indicates that you are using S-VIDEO terminal to receive signals.
6.
VIDEO
MONITOR OUT terminal outputs video signal receiving from RF, S-VIDEO or VIDEO terminal to
external equipment. When receiving component signals (Y
P
B
/C
B
P
R
/C
R
) or HDMI INPUT interface signal,
there is no output from
VIDEO
MONITOR OUT terminal.
7.
S-VIDEO
MONITOR OUT terminal outputs S-VIDEO signal receiving from S-VIDEIO inputs to external
equipment. When receiving signals from RF, VIDEO, Y, P
B
/C
B
, P
R
/C
R
terminals or HDMI INPUT interface,
there is no output from
S-VIDEO
MONITOR OUT terminal.
8.
FIXED/VARIABLE AUDIO
MONITOR OUT terminals provide fixed or variable audio level output to
external stereo system.
9.TV AS CENTER input jacks
These jacks are for stereo amplifiers with center signal output capability. This feature allows the TV speakers to
be used as a center speaker.