Hitachi CP-X3010N User Manual

Hitachi CP-X3010N - XGA LCD Projector Manual

Get Hitachi CP-X3010N - XGA LCD Projector PDF manuals and user guides
UPC - 050585151710
View all Hitachi CP-X3010N manuals
Add to My Manuals
Save this manual to your list of manuals

Hitachi CP-X3010N manual content summary:

  • Hitachi CP-X3010N | User Manual - Page 1
    Projector CP-X2010N/CP-X2510N/CP-X3010N User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read "Safety Guide DDC are trademarks of the Video Electronics Standard Association. • 
  • Hitachi CP-X3010N | User Manual - Page 2
    execute Projector 4 INPUT menu 32 Control panel 5 Rear panel 5 Remote control 6 Progressive, Video nr, Color space, Component, Video format Lamp time, Filter time, Turning off the power 15 My button, My source, Service Operating 16 NETWORK menu 51 Adjusting the volume 16 Setup, Projector
  • Hitachi CP-X3010N | User Manual - Page 3
    Remote control with two AA batteries (2) Power cord (3) Computer cable (4) Lens cover (2) (6) (5) User's manuals (Book x1, CD x1) (3) (6) Security label NOTE • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector
  • Hitachi CP-X3010N | User Manual - Page 4
    Part names Part names Projector (1) Lamp cover (&62) The lamp unit is inside. (2) Focus ring (&19) (3) Zoom ring (&19) (4) Control panel (&5) (5) Elevator buttons (x 2) (&19) (6) Elevator feet (x 2) (&19) (7) Remote sensor (&13) (8) Lens (&67) (9) Intake vents (10) F ilter cover (&64) The air
  • Hitachi CP-X3010N | User Manual - Page 5
    (&69) (6) LAMP indicator (&69) VIDEO port (12) AUDIO IN3 (R, L) ports (13) AUDIO OUT (R, L) ports (14) LAN port (&10) (15) Battery slot (&66) (15) (11) BAT TERY (5) (6) BAT TERY (4) (2) (1) (14) (3) LAN (10) (9) (12) (13) (8) (7) CAUTION ►Use the shutdown switch only when the projector
  • Hitachi CP-X3010N | User Manual - Page 6
    Part names Remote control (1) VIDEO button (&17) (2) COMPUTER button (&17) (2) (1) (3) SEARCH button (&18) (6) (4) STANDBY/ON (25) RESET button (&14, 23) (26) Battery cover (&13) MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME ON UP 㧗 DOWN OFF
  • Hitachi CP-X3010N | User Manual - Page 7
    . • For the case of installation in a special state such as ceiling mount, the specified mounting accessories (&74) and service may be required. Before installing the projector, consult your dealer about your installation. a Screen size (diagonal) type (inch) m 30 0.8 40 1.0 50 1.3 60 1.5 70 1.8 80
  • Hitachi CP-X3010N | User Manual - Page 8
    , and leave installing and removing the projector with the mounting accessories to the service personnel. • Read and keep the user's manual of the mounting accessories used. CAUTION ►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause fire
  • Hitachi CP-X3010N | User Manual - Page 9
    devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices USB RS-232C LAN BAT TERY L R S-VIDEO OUT AUDIO OUT VIDEO OUT L R AUDIO OUT L R Y CB/PB CR/PR AUDIO OUT COMPONENT VIDEO OUT VCR/DVD player L R AUDIO IN Speakers
  • Hitachi CP-X3010N | User Manual - Page 10
    port of the external device to communicate as a network terminal. See the User's Manual - Network Guide for details of network functions. External device Computer LAN RS-232C LAN BAT TERY WARNING ►Do not disassemble or modify the projector and accessories. ►Be careful not to damage the cables
  • Hitachi CP-X3010N | User Manual - Page 11
    with screws. • When connecting a laptop PC to the projector, be sure to activate the PC's external RGB output. (Set the laptop PC to CRT display or to simultaneous LCD and CRT display.) For details on how this is done, please refer to the instruction manual of the corresponding laptop PC. • When the
  • Hitachi CP-X3010N | User Manual - Page 12
    chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool. Anti-theft chain or wire Security slot Security bar WARNING ►Do not use
  • Hitachi CP-X3010N | User Manual - Page 13
    that could block the remote control's signal to the projector. • The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter fluorescent lamp) shines on the remote sensor of the projector. Adjust the position
  • Hitachi CP-X3010N | User Manual - Page 14
    REMOTE FREQ. in the SERVICE item of the OPTION menu (47) of the projector to be controlled should be set to the same mode as the remote port MY SOURCE/ VIDEO COMPUTER DOC.CAMERA your computer's manuals before connecting projector is working properly. This function is not available while the lamp
  • Hitachi CP-X3010N | User Manual - Page 15
    indicator is steady orange (69). Then remove the lens cover. 3. Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME UP ON 㧗 DOWN OFF ࡯ KEYSTONE
  • Hitachi CP-X3010N | User Manual - Page 16
    SETUP menu (36). Temporarily muting the sound 1. Press MUTE button on the remote control. A dialog will appear on the screen indicating that you have muted IN 2 VIDEO S-VIDEO COMPONENT (Y, Cb/Pb, Cr/Pr) ● While ON is selected for AUTO SEARCH item in OPTION menu (43), the projector will keep
  • Hitachi CP-X3010N | User Manual - Page 17
    will check COMPUTER IN1 port first. DOWN OFF ࡯ KEYSTONE MY BUTTON MUTE 1 2 POSITION MENU ESC ENTER RESET 1. Press VIDEO button on the remote control. Each time you press the button, the projector switches its input port from the current port as below. COMPONENT (Y, Cb/Pb, Cr/Pr
  • Hitachi CP-X3010N | User Manual - Page 18
    ratio 1. Press ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn.  F or a computer signal NORMAL  4:3  16:9  16:10  F or a video signal, s-video signal or component video signal 4:3  16:9  14:9 ASPECT button MY
  • Hitachi CP-X3010N | User Manual - Page 19
    the elevator feet. 4. After making sure that the elevator feet are locked, put the projector down gently. 5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet. 1 5 To loose an elevator foot, push the elevator button
  • Hitachi CP-X3010N | User Manual - Page 20
    or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (46).MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK Adjusting the position 1. Press POSITION button on the remote control when no menu is indicated. The "POSITION" indication will
  • Hitachi CP-X3010N | User Manual - Page 21
    automatic vertical keystone correction. (2) MANUAL displays a dialog for keystone correction. after a few seconds. MY SOURCE/ VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK OFF RESET button of MAGNIFY on the remote control. ● The projector automatically exits from the MAGNIFY mode when
  • Hitachi CP-X3010N | User Manual - Page 22
    FREEZE button on the remote control. The "FREEZE" indication will appear on the screen (however, MY SOURCE/ VIDEO COMPUTER DOC.CAMERA the indication will not appear when the OFF is selected for ASPECT AUTO SEARCH BLANK the MESSAGE item in the SCREEN menu (40)), and the projector will go into
  • Hitachi CP-X3010N | User Manual - Page 23
    menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, MY SOURCE/ SECURITY and EASY MENU. VIDEO COMPUTER DOC.CAMERA item will appear. (3) Use the buttons as instructed in the OSD to operate the item. (continued on next page) 23
  • Hitachi CP-X3010N | User Manual - Page 24
    ● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) previous display, press the ◄ cursor button or ESC button on the remote control. Indication in OSD (On Screen Display) The meanings of the general
  • Hitachi CP-X3010N | User Manual - Page 25
    EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. EASY MENU Item Description ASPECT Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE
  • Hitachi CP-X3010N | User Manual - Page 26
    LANGUAGE item in SCREEN menu (38). Press the ► or ENTER button to use the menu of PICTURE, ADVANCED MENU IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or SECURITY. EXIT Press the ◄ or ENTER button to finish the OSD menu. 26
  • Hitachi CP-X3010N | User Manual - Page 27
    PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. PICTURE menu Item BRIGHTNESS CONTRAST Description
  • Hitachi CP-X3010N | User Manual - Page 28
    , but it is not a malfunction. COLOR Using the ◄/► buttons adjusts the strength of whole color. Weak ó Strong • This item can be selected only for a video, s-video and component video signal. TINT Using the ◄/► buttons adjusts the tint. Reddish ó Greenish • This item can be selected only for
  • Hitachi CP-X3010N | User Manual - Page 29
    MY MEMORY Description This item is available only for CP-X2510N or CP-X3010N. Using the ▲/▼ cursor buttons changes the active iris when the PRESENTATION or THEATER modes are selected. If this occurs select OFF. This projector has 4 memories for adjustment data (for all the items of the PICTURE menu
  • Hitachi CP-X3010N | User Manual - Page 30
    ◄/► buttons adjusts the over-scan ratio. Small (It magnifies picture) ó Large (It reduces picture) • This item can be selected only for a video, s-video and component video signal. • When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case
  • Hitachi CP-X3010N | User Manual - Page 31
    reset the adjustment by pressing the RESET button on the remote control during this operation. • Images might appear degraded when bright picture when adjusting. For a video signal and s-video signal The video format best suited for the respective input SERVICE item in the OPTION menu (46). 31
  • Hitachi CP-X3010N | User Manual - Page 32
    , Cr/Pr) port. COMPONENT ó SCART RGB When the SCART RGB is selected, the COMPONENT (Y, Cb/ Pb, Cr/Pr) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer. (continued on next page) 32
  • Hitachi CP-X3010N | User Manual - Page 33
    buttons to select the computer input signal type. AUTO ó SYNC ON G OFF • Selecting the AUTO mode allows you to input a sync on G signal or component video signal from the port. • In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so
  • Hitachi CP-X3010N | User Manual - Page 34
    COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ vertical (VERT) resolutions using CUSTOM ↓ the buttons. This function is may not support all resolutions. (5) Move the cursor to OK on screen and press the
  • Hitachi CP-X3010N | User Manual - Page 35
    to the (forward/backward) setup angle by itself. This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again. • The adjustable range of this function will vary among inputs. For some input, this function may not work
  • Hitachi CP-X3010N | User Manual - Page 36
    232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode. If input port using ▲/▼ buttons. COMPUTER IN1 ó COMPUTER IN2  STANDBY  COMPONENT VIDEO ó S-VIDEO ó (Y, Cb/Pb, Cr/Pr) • Choose STANDBY, to select the
  • Hitachi CP-X3010N | User Manual - Page 37
    ) is automatically activated when is selected and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPONENT, COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN
  • Hitachi CP-X3010N | User Manual - Page 38
    or INPUT button to save the language setting. Using the buttons adjusts the menu position. To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds. Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for
  • Hitachi CP-X3010N | User Manual - Page 39
    frame for capturing will appear. To stop performing, press the RESET button on the remote control. 2. Using the buttons adjusts the frame position. Please move the frame the previous dialog, press the RESET button on the remote control. Registration takes several minutes. When the registration is
  • Hitachi CP-X3010N | User Manual - Page 40
    SCREEN menu Item Description MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON ó OFF When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the
  • Hitachi CP-X3010N | User Manual - Page 41
    SCREEN menu Item Description SOURCE NAME Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE
  • Hitachi CP-X3010N | User Manual - Page 42
    sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not which is for additional information such as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C. program
  • Hitachi CP-X3010N | User Manual - Page 43
    button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table OPTION when an input is found, the projector will stop searching and display the image. COMPUTER IN1  COMPUTER IN2 VIDEO ï S-VIDEO ï COMPONENT (Y, Cb/Cr, Cr/
  • Hitachi CP-X3010N | User Manual - Page 44
    to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the
  • Hitachi CP-X3010N | User Manual - Page 45
    item is available only for CP-X2510N or CP-X3010N.) • PICTURE MODE: Changes the off (Messenger Function of the User's Manual - Network Guide). When there is no transferred remote control. Select the picture input that is connected with a document camera. COMPUTER IN1  COMPUTER IN2 VIDEO  S-VIDEO
  • Hitachi CP-X3010N | User Manual - Page 46
    the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. FAN SPEED Using the ▲/▼ buttons switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is
  • Hitachi CP-X3010N | User Manual - Page 47
    remote control. REMOTE FREQ. (1)Use the ▲/▼ button to change the projector's remote sensor frequency setting (4). 1:NORMAL ó 2:HIGH (2)Use the ◄/► button to change the projector's remote function of serial communication, refer to the User's Manual - Network Guide. (continued on next page) 47
  • Hitachi CP-X3010N | User Manual - Page 48
    from the computer. The CONTROL port doesn't accept RS-232C commands.(Controlling the external device via the projector (using the NETWORK BRIDGE function) of the User's Manual - Network Guide) OFF: Select this mode to receive RS-232C commands using the CONTROL port. • OFF is selected as the
  • Hitachi CP-X3010N | User Manual - Page 49
    receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port. OFF ó 1s ó 2s ó 3s SERVICE (continued) OFF: Select this mode if it is not required to check the responses from the device that the projector sends data to. In this mode, the
  • Hitachi CP-X3010N | User Manual - Page 50
    a dialog titled "INPUT_INFORMATION". It shows the information about the current input. SERVICE (continued) • The "FRAME LOCK" message on the dialog means the setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY settings are not reset. CANCEL  OK 50
  • Hitachi CP-X3010N | User Manual - Page 51
    control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. See the User's Manual - Network Guide for details of NETWORK operation. NOTE • If you are not utilizing SNTP (Date
  • Hitachi CP-X3010N | User Manual - Page 52
    Use the buttons to enter the Year (last two digits), Month, Date, Hour and Minute. • The projector will override this setting and retrieve DATE AND TIME information from the Time server when SNTP is enabled. ( Date/Time Settings of the User's Manual - Network Guide) (continued on next page) 52
  • Hitachi CP-X3010N | User Manual - Page 53
    NAME Description (1) Use the ▲/▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECTOR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the first 3 lines. If not yet written, the lines will be blank. Use the buttons
  • Hitachi CP-X3010N | User Manual - Page 54
    projector. Use the ▲/▼ buttons to select an item which is a still image by the MY IMAGE ( MY IMAGE (Still Image Transfer) Display of the User's Manual - Network Guide displayed and its source file in the projector. (1) P ress the RESET button on the remote control while displaying an image to
  • Hitachi CP-X3010N | User Manual - Page 55
    indicate "0.0.0.0" when DHCP is ON and the projector has not gotten address from DHCP server. Executing this item restarts and initializes the network functions. Choose the RESTART EXECUTE using the button ►. SERVICE Then use the button ► to execute. Network will be once cut off when choose
  • Hitachi CP-X3010N | User Manual - Page 56
    projector. (2). The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user this time. Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box. • Please do
  • Hitachi CP-X3010N | User Manual - Page 57
    of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu. When a password is set Code. Your password will be sent after your user registration information is confirmed. (continued on next page) 57
  • Hitachi CP-X3010N | User Manual - Page 58
    be displayed. • If there is no key input for about 5 minutes while the Inquiring Code is displayed, the projector will turn off. 3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will be sent after your user registration information is confirmed. (continued on next page) 58
  • Hitachi CP-X3010N | User Manual - Page 59
    projector will not display the input signal. • To display the signal again, set this function OFF. • After about 5 minutes of displaying the TRANSITION DETECTOR ON alarm, the lamp remote control or the ► button on the projector user registration information is confirmed. (continued on next page) 59
  • Hitachi CP-X3010N | User Manual - Page 60
    note of the password during this time. Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu. 2 Turning off the Your password will be sent after your user registration information is confirmed. (continued on next page) 60
  • Hitachi CP-X3010N | User Manual - Page 61
    When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen. • This function is available only when the MY TEXT PASSWORD function is set to the OFF. MY TEXT WRITING (1) U se the ▲/▼ buttons
  • Hitachi CP-X3010N | User Manual - Page 62
    . Handles 4 6. While putting the interlocking parts of the lamp cover and the projector together, slide the lamp cover back in place. Then firmly fasten the screw of the lamp cover. 7. Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu. (1) Press the MENU
  • Hitachi CP-X3010N | User Manual - Page 63
    used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, consult your local dealer or a service representative. • Handle with care: jolting or scratching could cause the lamp bulb to burst during use. • Using the lamp for long periods of time, could cause
  • Hitachi CP-X3010N | User Manual - Page 64
    will come together with a replacement lamp for this projector. 1. Turn the projector off, and unplug the power cord. Allow the projector to sufficiently cool down. Filter cover 2 2. Use a vacuum cleaner on and around the filter cover. 3. While supporting the projector with one hand, use your
  • Hitachi CP-X3010N | User Manual - Page 65
    the air filter when it is damaged or heavily soiled. • When you replace the projection lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector. • Please reset the filter time only when you have cleaned or replaced the air
  • Hitachi CP-X3010N | User Manual - Page 66
    HITACHI MAXELL, part number CR2032 or CR2032H. Slot Cover 1. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2. After making sure that the projector battery. For setting the clock, see the User's Manual - Network Guide. WARNING ►Be careful of handling a
  • Hitachi CP-X3010N | User Manual - Page 67
    not touch the lens directly with your hand. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc. 1. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2. After making sure that the
  • Hitachi CP-X3010N | User Manual - Page 68
    to your dealer or service company. Otherwise if a problem occurs with the projector, the following checks and measures are recommended before requesting repair. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied
  • Hitachi CP-X3010N | User Manual - Page 69
    Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP indicator indicator indicator Description Lighting Turned Turned The projector is in a standby state.
  • Hitachi CP-X3010N | User Manual - Page 70
    remedy, please set FAN SPEED of SERVICE item in OPTION menu to HIGH projector. Please refer to "Schedule Settings" section of User's Manual - Network Guide. NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps
  • Hitachi CP-X3010N | User Manual - Page 71
    Troubleshooting , and allow the projector to cool down at least 10 minutes, then turn the power on again. Either there is no lamp and/or lamp cover, or either Correctly set up the signal source device by referring to the manual of the source device. The input changeover settings are mismatched.
  • Hitachi CP-X3010N | User Manual - Page 72
    Troubleshooting level using the menu function. 27 The computer cannot detect the projector as a plug and play monitor. Make sure that the Video screen display freezes. Colors have a faded- out appearance, or Color tone is poor. The BLANK screen is displayed. Press BLANK button on the remote
  • Hitachi CP-X3010N | User Manual - Page 73
    Troubleshooting in the SETUP 35 menu. The lamp is approaching the end of its product lifetime. Replace the lamp. 62, 63 Pictures appear blurry. Either is set to NETWORK BRIDGE. Select OFF for COMMUNICATION TYPE item in the 48 OPTION - SERVICE - COMMUNICATION menu. Network does not work
  • Hitachi CP-X3010N | User Manual - Page 74
    Lens Lamp Speaker Power supply Power consumption Temperature range Size Weight (mass) Ports Optional parts Specification Liquid crystal projector 786, OUT D-sub 15 pin mini x1 Video input port Y, Cb/Pb, Cr/Pr (Component video RCA x3 S-VIDEO mini DIN 4 pin x1 VIDEO RCA x1 Audio input/output port
  • Hitachi CP-X3010N | User Manual - Page 75
    Specifications (continued) Specifications 118 130 288 317 [unit: mm] 75
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
1
Projector
CP-X2010N/CP-X2510N/CP-X3010N
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
►Before using this product, please read all manuals for this
product. Be sure to read “
Safety Guide
” first. After reading them, store them in a
safe place for future reference.
WARNING
• The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
NOTE
Trademark acknowledgment
Various symbols are used in this manual. The meanings of these symbols are
described below.
About this manual
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
• Mac
®
is a registered trademark of Apple Inc.
• Windows
®
is a registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
• Trademark PJLink is a trademark applied for trademark
rights in Japan, the United States of America and other
countries and areas.
All other trademarks are the properties of their respective owners.
NOTICE
This entry notices of fear of causing trouble.