Home » Honeywell Manuals » Barcode Scanners » Honeywell 1900GSR-2 » Manual Viewer

Honeywell 1900GSR-2 User Guide - Page 276

Replacing an Interface Cable, Replacing Cables and Batteries in Cordless Systems

View all Honeywell 1900GSR-2 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 276 highlights

• Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing an Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner's cable from the terminal or computer. 3. Locate the small hole on the back of the scanner's handle. This is the cable release. 4. Straighten one end of a paper clip. 5. Insert the end of the paper clip into the small hole and press in. This depresses the retention tab, releasing the connector. Pull the connector out while maintaining pressure on the paper clip, then remove the paper clip. Cable Release 6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Replacing Cables and Batteries in Cordless Systems Replacing an Interface Cable in a Base 1. Turn the power to the host system OFF. 2. Disconnect the base's cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip. 5. Replace with the new cable. Insert the connector into the opening 13 - 2

Section	Page
Xenon™ 1900/1902 User’s Guide	1
Table of Contents	13
Getting Started	23
About This Manual	23
Unpacking Your Device	23
Connecting the Device	24
Connecting with USB	24
Connecting with Keyboard Wedge	25
Connecting with RS232 Serial Port	27
Connecting with RS485	28
Reading Techniques	30
Menu Bar Code Security Settings	30
Setting Custom Defaults	31
Resetting the Custom Defaults	31
Resetting the Factory Defaults	32
Programming the Interface	33
Introduction	33
Programming the Interface - Plug and Play	33
Keyboard Wedge	33
Laptop Direct Connect	33
RS232 Serial Port	34
RS485	34
RS485 Packet Mode	35
USB IBM SurePos	36
USB PC or Macintosh Keyboard	36
USB HID	37
USB Serial	37
Verifone® Ruby Terminal Default Settings	38
Gilbarco® Terminal Default Settings	39
Honeywell Bioptic Aux Port Configuration	39
Datalogic™ Magellan© Bioptic Aux Port Configuration	39
NCR Bioptic Aux Port Configuration	40
Wincor Nixdorf Terminal Default Settings	40
Wincor Nixdorf Beetle™ Terminal Default Settings	41
Keyboard Country Layout	42
Keyboard Style	49
Keyboard Conversion	50
Control Character Output	51
Keyboard Modifiers	51
RS232 Baud Rate	54
RS232 Word Length: Data Bits, Stop Bits, and Parity	55
RS232 Receiver Time-Out	56
RS232 Handshaking	56
RS232 Timeout	57
XON/XOFF	57
ACK/NAK	57
Scanner to Bioptic Communication	58
Scanner-Bioptic Packet Mode	58
Scanner-Bioptic ACK/NAK Mode	59
Scanner-Bioptic ACK/NAK Timeout	59
Cordless System Operation	61
How the Cordless Charge Base/Access Point Works	61
Linking the Scanner to a Charge Base	61
Linking the Scanner to an Access Point	62
Communication Between the Cordless System and the Host	62
RF (Radio Frequency) Module Operation	63
System Conditions	63
Linking Process	63
Scanner Is Out of Range	64
Scanner Is Moved Back Into Range	64
Out of Range and Back into Range with Batch Mode On	64
Page Button	64
About the Battery	64
Charging Information	65
Battery Recommendations	65
Proper Disposal of the Battery	66
Beeper and LED Sequences and Meaning	66
Scanner LED Sequences and Meaning	67
Base/Access Point LED Sequences and Meaning	67
Base Power Communication Indicator	68
Reset Scanner	68
Scanning while in Base Cradle	68
Paging	69
Paging Mode	69
Paging Pitch	69
Error Indicators	69
Beeper Pitch - Base Error	69
Number of Beeps - Base Error	70
Scanner Report	70
Scanner Address	71
Base or Access Point Address	71
Scanner Modes	71
Charge Only Mode	71
Linked Modes	72
Unlinking the Scanner	73
Override Locked Scanner	73
Out-of-Range Alarm	73
Alarm Sound Type	74
Flexible Power Management	75
Batch Mode	76
Batch Mode Beep	77
Batch Mode Storage	77
Batch Mode Quantity	78
Batch Mode Output Order	80
Delete Last Code	80
Clear All Codes	80
Transmit Records to Host	81
Batch Mode Transmit Delay	81
Multiple Scanner Operation	81
Scanner Name	82
Application Work Groups	84
Application Work Group Selection	85
Resetting the Factory Defaults: All Application Work Groups	85
Resetting the Custom Defaults: All Application Work Groups	86
Using the Scanner with Bluetooth Devices	86
PCs/Laptops	86
PDAs/Mobility Systems Devices	87
Changing the Scanner’s Bluetooth PIN Code	87
Minimizing Bluetooth/ISM Band Network Activity	87
Auto Reconnect Mode	88
Maximum Link Attempts	89
Relink Time-Out	90
Bluetooth/ISM Network Activity Examples	90
Host Command Acknowledgment	91
Input/Output Settings	95
Power Up Beeper	95
Beep on BEL Character	95
Trigger Click	96
Good Read and Error Indicators	96
Beeper – Good Read	96
Beeper Volume – Good Read	97
Beeper Pitch – Good Read	97
Beeper Pitch – Error	98
Beeper Duration – Good Read	98
LED – Good Read	98
Number of Beeps – Good Read	99
Number of Beeps – Error	99
Good Read Delay	100
User-Specified Good Read Delay	100
Manual/Serial Trigger Modes	100
Manual Trigger	100
Serial Trigger	101
Presentation Mode	103
Presentation LED Behavior after Decode	103
Presentation Sensitivity	103
In-Stand Sensor Mode	104
Streaming Presentation™ Mode	104
Streaming Presentation In-Stand Programming	105
Mobile Phone Read Mode	105
Image Snap and Ship	106
Hands Free Time-Out	106
Reread Delay	106
User-Specified Reread Delay	107
Illumination Lights	107
Aimer Delay	108
User-Specified Aimer Delay	108
Scanner Time-Out	108
Aimer Mode	109
Centering	109
Preferred Symbology	111
High Priority Symbology	111
Low Priority Symbology	112
Preferred Symbology Time-out	112
Preferred Symbology Default	112
Output Sequence Overview	113
Require Output Sequence	113
Output Sequence Editor	113
To Add an Output Sequence	113
Other Programming Selections	114
Output Sequence Editor	115
Partial Sequence	115
Require Output Sequence	116
Multiple Symbols	116
No Read	117
Video Reverse	118
Data Editing	119
Prefix/Suffix Overview	119
To Add a Prefix or Suffix:	119
To Clear One or All Prefixes or Suffixes	120
To Add a Carriage Return Suffix to All Symbologies	121
Prefix Selections	121
Suffix Selections	122
Function Code Transmit	122
Intercharacter, Interfunction, and Intermessage Delays	122
Intercharacter Delay	123
User Specified Intercharacter Delay	123
Interfunction Delay	124
Intermessage Delay	124
Data Formatting	125
Data Format Editor Introduction	125
To Add a Data Format	125
Other Programming Selections	127
Terminal ID Table	128
Data Format Editor Commands	128
Move Commands	129
Search Commands	130
Miscellaneous Commands	131
Data Formatter	132
Data Format Non-Match Error Tone	133
Primary/Alternate Data Formats	134
Single Scan Data Format Change	134
Symbologies	137
All Symbologies	138
Message Length Description	138
Codabar	139
Codabar Concatenation	140
Code 39	142
Code 32 Pharmaceutical (PARAF)	144
Full ASCII	145
Code 39 Code Page	145
Interleaved 2 of 5	146
NEC 2 of 5	148
Code 93	150
Code 93 Code Page	150
Straight 2 of 5 Industrial (three-bar start/stop)	151
Straight 2 of 5 IATA (two-bar start/stop)	152
Matrix 2 of 5	153
Code 11	154
Code 128	155
ISBT 128 Concatenation	155
Code 128 Code Page	156
GS1-128	157
Telepen	158
UPC-A	159
UPC-A/EAN-13 with Extended Coupon Code	161
UPC-E0	162
UPC-E1	165
EAN/JAN-13	165
ISBN Translate	167
EAN/JAN-8	168
MSI	170
GS1 DataBar Omnidirectional	172
GS1 DataBar Limited	172
GS1 DataBar Expanded	173
Trioptic Code	174
Codablock A	174
Codablock F	176
PDF417	177
MicroPDF417	178
GS1 Composite Codes	179
UPC/EAN Version	179
GS1 Emulation	180
TCIF Linked Code 39 (TLC39)	181
QR Code	181
Data Matrix	183
MaxiCode	184
Aztec Code	185
Chinese Sensible (Han Xin) Code	186
Postal Codes - 2D	187
Single 2D Postal Codes:	187
Combination 2D Postal Codes:	188
Postal Codes - Linear	190
China Post (Hong Kong 2 of 5)	190
Korea Post	192
Imaging Commands	193
Single-Use Basis	193
Command Syntax	193
Image Snap - IMGSNP	194
IMGSNP Modifiers	194
Image Ship - IMGSHP	197
IMGSHP Modifiers	197
Intelligent Signature Capture - IMGBOX	206
Signature Capture Optimize	206
IMGBOX Modifiers	207
RF Default Imaging Device	211
Interface Keys	213
Keyboard Function Relationships	213
Supported Interface Keys	215
Utilities	221
To Add a Test Code I.D. Prefix to All Symbologies	221
Show Decoder Revision	221
Show Scan Driver Revision	221
Show Software Revision	221
Show Data Format	222
Test Menu	222
TotalFreedom	222
Application Plug-Ins (Apps)	223
EZConfig Introduction	223
Installing EZConfig from the Web	224
Serial Programming Commands	227
Conventions	227
Menu Command Syntax	227
Query Commands	228
Responses	229
Trigger Commands	230
Resetting the Custom Defaults	230
Menu Commands	231
Product Specifications	267
1900 Scanner Product Specifications	267
1902 Scanner Product Specifications	268
CCB01-010BT Charge Base Product Specifications	269
Standard Cable Pinouts	270
Keyboard Wedge	270
Serial Output	271
RS485 Output	272
USB	273
Maintenance	275
Repairs	275
Maintenance	275
Cleaning the Device	275
Inspecting Cords and Connectors	275
Replacing Cables in Corded Scanners	275
Replacing an Interface Cable	276
Replacing Cables and Batteries in Cordless Systems	276
Replacing an Interface Cable in a Base	276
Changing a scanner Battery	277
Troubleshooting a Xenon Scanner	277
Troubleshooting a Cordless System	278
Troubleshooting a Base	278
Troubleshooting a Cordless Scanner	279
Customer Support	281
Reference Charts	285
Symbology Chart	285
ASCII Conversion Chart (Code Page 1252)	288
Code Page Mapping of Printed Barcodes	290
Sample Symbols	293