Honeywell 3800gPDF User Guide - Page 40

Automatic Trigger, Presentation Mode, Continuous Illumination Mode, Hands Free Time-Out

Get Honeywell 3800gPDF - Hand Held Decoding Linear Imager PDF manuals and user guides View all Honeywell 3800gPDF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

ger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. Default = 30,000. Read Time-Out Automatic Trigger The imager scans continuously using internal LEDs to detect bar codes. Automatic Trigger Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LEDs are off for ambient conditions until a change occurs in the imager's field of view. Then the LEDS turn on automatically to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly. Presentation Mode Continuous Illumination Mode If you have several bar codes that are close together, you may wish to have a continuous aiming beam on in order to properly aim the imager at one bar code. Scan the Continuous Illumination On bar code to program the imager for this capability. Once you have the aiming beam over the correct bar code, pull the trigger to read the code. Scan the Continuous Illumination Off bar code to turn off this feature. Continuous Illumination Mode On Hands Free Time-Out * Continuous Illumination Mode Off The Automatic Trigger and Presentation Modes are referred to as "hands free" modes. If the imager's trigger is pulled when using a hands free mode, the imager changes to manual trigger mode. You can set the time the imager should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the imager reverts to the original hands free mode. 3 - 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
3 - 4
ger command.
After scanning the
Read Time-Out
bar code, set the time-out
duration (from 0-300,000 milliseconds) by scanning digits from the inside back
cover, then scanning
Save
.
Default = 30,000.
Automatic Trigger
The imager scans continuously using internal LEDs to detect bar codes.
Presentation Mode
Presentation Mode uses ambient light to detect bar codes.
The LEDs are off for
ambient conditions until a change occurs in the imager’s field of view.
Then the
LEDS turn on automatically to read the code.
If the light level in the room is not
high enough, Presentation Mode may not work properly.
Continuous Illumination Mode
If you have several bar codes that are close together, you may wish to have a
continuous aiming beam on in order to properly aim the imager at one bar code.
Scan the
Continuous Illumination On
bar code to program the imager for this
capability.
Once you have the aiming beam over the correct bar code, pull the
trigger to read the code.
Scan the
Continuous Illumination Off
bar code to
turn off this feature.
Hands Free Time-Out
The Automatic Trigger and Presentation Modes are referred to as “hands free”
modes.
If the imager’s trigger is pulled when using a hands free mode, the
imager changes to manual trigger mode.
You can set the time the imager
should remain in manual trigger mode by setting the Hands Free Time-Out.
Once the time-out value is reached, (if there have been no further trigger pulls)
the imager reverts to the original hands free mode.
Read Time-Out
Automatic Trigger
Presentation Mode
Continuous Illumination Mode On
* Continuous Illumination Mode Off