Honeywell 4800dr Barcode Guide - Page 26

User-Specified Reread Delay, LED Power Level, Imager Time-Out, Default = High.

Get Honeywell 4800dr - Document Camera PDF manuals and user guides View all Honeywell 4800dr manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

User-Specified Reread Delay If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. User-Specified Reread Delay LED Power Level This selection allows you to adjust LED and aimer brightness. Off is used when no illumination is needed. Low is used if low illumination is sufficient. High (the default) is the brightest setting. If you have an aimer delay programmed (see Aimer Delay on page 3-7), the aimer will be at 100% power during the delay, regardless of the LED Power Level. Default = High. Note: If you scan the Off barcode, both the aimer and illumination lights turn off, making it impossible to scan barcodes in low light. To turn the LED Power Level back on, move to a brightly lit area and scan either the Low or the High barcode below. Off Low (50%) * High (100%) Imager Time-Out Imager Time-Out powers down the document reader after the unit has been idle for the specified time. To prevent the document reader from powering down, set this time-out to 0. Scan the barcode below, then set the time-out by scanning digits (from 0 - 999,999 ms) from the inside back cover, then scanning Save. Default = 60,000 ms. Imager Time-Out 3 - 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
3 - 6
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from
0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning
Save
.
LED Power Level
This selection allows you to adjust LED and aimer brightness.
Off
is used when no illumination is
needed.
Low
is used if low illumination is sufficient.
High
(the default) is the brightest setting.
If you have an aimer delay programmed (see
Aimer Delay
on page 3-7), the aimer will be at 100% power
during the delay, regardless of the LED Power Level.
Default = High.
Note:
If you scan the
Off
barcode, both the aimer and illumination lights turn off, making it impossible
to scan barcodes in low light.
To turn the LED Power Level back on, move to a brightly lit area
and scan either the
Low
or the
High
barcode below.
Imager Time-Out
Imager Time-Out powers down the document reader after the unit has been idle for the specified time.
To prevent the document reader from powering down, set this time-out to 0.
Scan the barcode below,
then set the time-out by scanning digits (from 0 - 999,999 ms) from the inside back cover, then scanning
Save
.
Default = 60,000 ms.
User-Specified Reread Delay
Off
Low (50%)
*
High (100%)
Imager Time-Out