Honeywell MK1650-62B14 User Guide - Page 19

IBM 46xx IS1650-106

Get Honeywell MK1650-62B14 - Metrologic IS1650 - Wired Stationary Barcode Scanner PDF manuals and user guides View all Honeywell MK1650-62B14 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

INSTALLATION CABLE INSTALLATION (INTERFACE SPECIFIC) IBM 46xx IS1650-106 1. Turn off the host device. 2. Plug the male 10-pin RJ45 end of the MVC cable into the 10-pin socket on the IS1650. There will be an audible click when the connector lock engages. 3. Connect the other end of the MVC cable to the host device. 4. Turn on the host device. 5. The IS1650 will start to initialize. All LEDs (yellow, white, and blue) will light for approximately two seconds then start to alternately flash. When the scanner has finished initializing the LEDs will stop flashing and the unit will beep three times indicating that the scanner is ready for use. Figure 11. Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system. The scanner is shipped from the factory configured with default settings. Please refer to the MetroSelect Single-Line Configuration Guide (MLPN 00-02544) or MetroSet2's help files for instructions on changing the scanner's configuration. In addition, please check that the scanner and host system are using the same communication protocol. See SELV Power caution statement located on page 10 of this manual. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
15
I
NSTALLATION
C
ABLE
I
NSTALLATION
(I
NTERFACE
S
PECIFIC
)
IBM 46xx IS1650-106
1.
Turn off the host device.
2.
Plug the male 10-pin RJ45 end of
the MVC cable into the 10-pin
socket on the IS1650.
There will be
an audible
click
when the connector
lock engages.
3.
Connect the other end of the MVC
cable to the host device.
4.
Turn on the host device.
5.
The IS1650 will start to initialize.
All LEDs (yellow, white, and blue)
will light for approximately
two seconds then start to
alternately flash.
When the scanner
has finished initializing the LEDs
will stop flashing and the unit will
beep three times indicating that the
scanner is ready for use.
Plugging the scanner into a port on the host system does not guarantee
that scanned information will be communicated properly to the host
system.
The scanner is shipped from the factory configured with default
settings.
Please refer to the MetroSelect Single-Line Configuration
Guide (
MLPN
00-02544) or MetroSet
2
’s help files for instructions on
changing the scanner’s configuration.
In addition, please check that the
scanner and host system are using the same communication protocol.
See SELV Power caution statement located on page 10 of this manual
.
Figure 11.