Hoover 72-59139 User Guide - Page 10
Carpet Cleaning, Picking up spills
View all Hoover 72-59139 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
To clean nozzle If lint or other debris becomes lodged in nozzle, do not attempt to remove nozzle cover. Pour one to two cups of clear water on a non-carpeted floor. Do not pour water onto a wood floor. Pick up the water with your deep cleaner. Repeat as necessary until debris is flushed out of nozzle. 4. To avoid walking on damp carpet, start at the end of the room farthest from the door or path to sink where tanks will be emptied and filled. Step on handle release pedal and lower handle to operating position; turn deep cleaner ON. 5. Squeeze trigger to release cleaning solution and slowly push deep cleaner forward (equals one wet stroke). 6. Continue to squeeze trigger and slowly pull deep cleaner back toward you (second wet stroke). Release trigger and slowly push deep cleaner forward over area just sprayed with solution (dry stroke). Then slowly pull deep cleaner back toward you without squeezing trigger (dry stroke). Continue going over the area with dry strokes until the green 'MAX Extract' light comes on. 7. Overlap strokes by 1 inch to help prevent streaking. Keep nozzle flat on floor for both forward and reverse strokes. 3-3 Some models have a nozzle clean-out tool for removing debris or if a non-carpeted floor is not available. To use the tool: Disconnect deep cleaner from electrical outlet. Slide tool into nozzle and remove debris as shown. 3-4 8. For heavily soiled areas, repeat steps 5-7. Avoid saturating carpet, as noted below. 9. For particularly soiled carpet or spots, use the Clean Surge™ button (see following section). Avoid saturating carpet, as noted below. Note: To avoid saturating carpet, do not use more than 4 wet strokes over one area. Always end with dry strokes. To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent. Do not use solvent or petroleum based products to clean the machine . Carpet Cleaning Read "Before you begin cleaning" instructions on page 9. 1. Fill clean solution tank (upper tank) with HOOVER Carpet/Upholstery Detergent according to instructions for Figs. 2-9 to 2-15. 2. Move speed selector to LO for gentle cleaning or Hl for normal cleaning. 3. Dry hands and plug cord into a properly grounded outlet. Do not clean over floor electrical outlets. It is best to alternate wet and dry strokes as described above. For best cleaning results and to aid in faster drying of carpet, end with more dry strokes. (Continue using dry strokes until little water is visible passing through the recovery tank lid and the green 'MAX Extract' light comes on.) 10. Empty recovery tank when the red 'MAX Extract' light comes on and the motor sound becomes higher pitched and there is a loss in suction (see "Automatic shut-off", Fig. 2-7) When finished cleaning, follow "After cleaning" instructions on pages 9 & 10. 3-5 Clean Surge™ Button The 'Clean Surge' button can be used to dispense extra solution when cleaning particularly soiled areas of carpet or spots. To use, press 'Clean Surge' button while squeezing solution trigger. For normal solution spray, release button and continue to squeeze solution trigger. Picking up spills Your deep cleaner may also be used to pick up small liquid spills (1 gallon or less, never to exceed 1/4 inch in depth) on carpet, upholstery, or bare floors. 1. For best results, pick up spills immediately by placing the stair/upholstery nozzle just above the spill and suction up any residue on top of the carpet. 2. If the spill remains, place either the stair/ upholstery nozzle or floor nozzle with brushes turned OFF in front of the spill, pull the nozzle very slowly over the spill initially with suction only. Repeat with spray and suction. 10 When picking up spills on bare floors, use only the floor nozzle with the bare floor attachment in place and speed selector in the OFF position (this will help prevent spreading the spill). If a spot is left, the stair/upholstery nozzle is generally more effective for removing it. Although no cleaning solution can completely remove all spots, they can be treated by following the instructions provided by the manufacturer of the carpet, upholstery, or bare floor surface being cleaned. Do not use the deep cleaner to pick up flammable or combustible liquids or ch e m i c a l s . When finished, follow "After cleaning" instructions on pages 9 & 10.