Hotpoint RB757WHWW Use and Care Manual / Warranty - Page 24

Using the self-cleaning oven.

Page 24 highlights

Consumer Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions Using the self-cleaning oven. (on some models) The oven door must be closed and all controls set correctly for the cycle to work properly. How to Delay the Start of Cleaning You can set the oven control to delay-start the oven, clean for a specific length of time and then turn off automatically. Make sure the clock shows the correct time of day. Follow the directions in the Before a Clean Cycle section. Latch the door. NOTE: Never force the latch. If the oven is too hot, you will not be able to slide the latch. Allow the oven to cool. Touch the SELF CLEAN pad. Touch the + or - pads to set the Clean Time. The Clean Time is preset for 4 hours and 20 minutes. You can change the Clean Time to any time between 3 and 5 hours, depending on the amount of soil in your oven. If a different Clean Time is desired, touch the + or - pads until the desired Clean Time is displayed. Touch the START TIME pad. Change the Start Time by touching the + or - pads. The start time will appear in the display. Touch the START/ON pad. The self-clean cycle will automatically begin at the time set. While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the SELF CLEAN pad. The oven shuts off automatically when the clean cycle is complete, and 0:00 will flash in the display. Slide the latch handle to the left as far as it will go and open the door. To Stop a Clean Cycle Touch the CLEAR/OFF pad. Wait until the oven has cooled below the locking temperature to unlatch the door. You will not be able to open the door right away unless the oven has cooled below the locking temperature. After a Clean Cycle You cannot set the oven for cooking until the oven is cool enough for the door to be unlatched. You may notice some white ash in the oven. Wipe it up with a damp cloth after the oven cools. If white spots remain, remove them with a soap-filled steel-wool pad and rinse thoroughly with a vinegar and water mixture. These deposits are usually a salt residue that cannot be removed by the clean cycle. If the oven is not clean after one clean cycle, repeat the cycle. ■ You cannot set the oven for cooking until the oven is cool enough for the door to unlock. ■ While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the COOKING TIME pad. ■ If the racks become hard to slide, apply a small amount of vegetable oil or cooking oil to a paper towel and wipe the edges of the oven racks with the paper towel. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

The oven door must be closed and all controls set correctly for the cycle to work properly.
After a Clean Cycle
You cannot set the oven for cooking until
the oven is cool enough for the door to be
unlatched.
You may notice some white ash in the oven.
Wipe it up with a damp cloth after the
oven cools.
If white spots remain, remove them with
a soap-filled steel-wool pad and rinse
thoroughly with a vinegar and water mixture.
These deposits are usually a salt residue that
cannot be removed by the clean cycle.
If the oven is not clean after one clean cycle,
repeat the cycle.
You cannot set the oven for cooking until
the oven is cool enough for the door
to unlock.
While the oven is self-cleaning, you can
touch the
CLOCK
pad to display the time
of day. To return to the clean countdown,
touch the
COOKING TIME
pad.
If the racks become hard to slide, apply a
small amount of vegetable oil or cooking oil
to a paper towel and wipe the edges of the
oven racks with the paper towel.
How to Delay the Start of Cleaning
You can set the oven control to delay-start
the oven, clean for a specific length of time
and then turn off automatically.
Make sure the clock shows the correct time
of day.
Follow the directions in the
Before a Clean
Cycle
section.
Latch the door.
NOTE:
Never force the latch. If the oven is
too hot, you will not be able to slide the latch.
Allow the oven to cool.
Touch the
SELF CLEAN
pad.
Touch the
+
or
pads to set the
Clean Time.
The Clean Time is preset for 4 hours and 20
minutes. You can change the Clean Time to
any time between 3 and 5 hours, depending
on the amount of soil in your oven. If a
different Clean Time is desired, touch
the
+
or
pads until the desired Clean Time
is displayed.
Touch the
START TIME
pad.
Change the Start Time by touching the
+
or
pads. The start time will appear in the display.
Touch the
START/ON
pad.
The self-clean cycle will automatically begin
at the time set.
While the oven is self-cleaning, you can touch
the
CLOCK
pad to display the time of day.
To return to the clean countdown, touch
the
SELF CLEAN
pad.
The oven shuts off automatically when
the clean cycle is complete, and 0:00 will flash
in the display.
Slide the latch handle to the left as far
as it will go and open the door.
To Stop a Clean Cycle
Touch the
CLEAR/OFF
pad.
Wait until the oven has cooled below the
locking temperature to unlatch the door. You
will not be able to open the door right away
unless the oven has cooled below the locking
temperature.
24
Consumer Support
Troubleshooting Tips
Care and Cleaning
Operating Instructions
Safety Instructions
Using the self-cleaning oven.
(on some models)