Hunter 25522 Owner's Manual - Page 8

operating your ceiling fan, cleaning your ceiling fan, troubleshooting - replacement blades

Page 8 highlights

8 operating your ceiling fan 1. Turn on electrical power to the fan. 2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector. cleaning your ceiling fan caring for finishes For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and a slightly dampened cloth. An artistic agent may be used, but never use abrasive cleaning agents as they will damage the finish. caring for blades The painted and high-gloss blade holders may be cleaned in the same manner as the fan finish. The sailcloth blade material should be wiped off with a damp cloth. troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Pull the pull chain to ensure it is on. 5. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade bracket screws until snug. 2. Tighten the blade screws until snug. 3. Check to see if the blade is cracked. If so, replace all the blades. 4. Change to an approved speed control. 5. Check and tighten the screws in the switch housing mounting plate and in the upper and lower switch housing. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade and/or blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 41877-01 06/14/2007 © 2007 Hunter Fan Company

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

41877-01
0
6
/1
4
/200
7
© 200
7
Hunter Fan Company
8
operating your ceiling fan
1.
Turn on electrical power to the fan.
2.
The fan pull chain controls power to the fan. The pull chain
has four settings in sequence: High, Medium, Low and Off.
Pull the chain slowly to change settings.
Release slowly to prevent the chain from recoiling into
the blades.
The chain uses a breakaway connector that separates if
the chain is jerked. If this happens, simply reinsert the chain
into the connector.
cleaning your ceiling fan
caring for finishes
For cleaning, a soft brush or lint-free cloth should be used to pre-
vent scratching the finish. A vacuum cleaner brush nozzle can re-
move heavier dust. Surface smudges or an accumulation of dirt and
dust can easily be removed by using a mild detergent and a slightly
dampened cloth. An artistic agent may be used, but never use abra-
sive cleaning agents as they will damage the finish.
caring for blades
The painted and high-gloss blade holders may be cleaned in the
same manner as the fan finish. The sailcloth blade material should
be wiped off with a damp cloth.
troubleshooting
Problem: Nothing happens; fan does not move.
1.
Turn power on, replace fuse, or reset breaker.
2.
Loosen canopy, check all connections according to the
wiring the fan
section.
3.
Check the plug connection in the switch housing.
4.
Pull the pull chain to ensure it is on.
5.
Remove the shipping bumpers.
Problem: Noisy operation.
1.
Tighten the blade bracket screws until snug.
2.
Tighten the blade screws until snug.
3.
Check to see if the blade is cracked. If so, replace all the
blades.
4.
Change to an approved speed control.
5.
Check and tighten the screws in the switch housing
mounting plate and in the upper and lower switch hous-
ing.
Problem: Excessive wobbling.
1.
If your fan wobbles when operating, use the enclosed bal-
ancing kit and instructions to balance the fan.
2.
Tighten all blade and/or blade iron screws.
3.
Turn power off, support fan very carefully, and check that
the hanger ball is properly seated.
If you need parts or service assistance, please call 888-830-1326 or
visit us at our WEB site at http://www.hunterfan.com.
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114