Hunter 28425 Operation Manual - Page 7

wiring the fan, installing the canopy, installing the canopy trim ring

Get Hunter 28425 PDF manuals and user guides View all Hunter 28425 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

7 White Black wiring the fan 1. Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. 2. Connect the wires as shown in Figure 15. To connect the wires, twist the bare metal leads together. Place a wire nut over the intertwined length of wire and twist clockwise until tight. CAUTION: Be sure no bare wire or wire strands are visible after making connections. All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, you should use a qualified electrician. Power Black Wires in White Ceiling Bare or Green 2 x 4 Brace Approved Connectors Green Ground Wire from Hanger Pipe Outlet Box Ceiling Plate Figure 16 - Rotating the fan 2. Hook the tab hole over the tab on the ceiling plate as shown in Figure 17. 3. Raise the canopy, be sure the holes in the canopy and the ceil- ing plate are aligned, and loosely assemble the canopy screws one at a time. When all three screws are assembled, securely tighten all three canopy screws. Refer to Figure 17. Tab Hole and Tab Canopy Screw Figure 17 - Installing the canopy installing the canopy trim ring 1. To easily install the canopy trim ring, locate the two tabs on the canopy trim ring. See Figure 18. FFigure 15 - Wiring the fan installing the canopy 1. Rotate the fan 180º clockwise from the initial position when hanging the fan. The arrows on the hanger ball and on the ceiling plate should be pointing in the same direction and should be pointing towards the tab hole on the canopy. Refer to Figure 16. © 2005 Hunter Fan Company Canopy Press Here when Removing Press Here when Removing Canopy Trim Ring Tab Figure 18 - Canopy trim ring 2. Take both hands and push the canopy trim ring up to the top of the canopy. See Figure 18. 3. The canopy trim ring will snap and lock into place on the canopy. removing the canopy trim ring 1. Locate the tab indicators, small bumps on top of tabs. Refer to Figure 19. 2. To remove the canopy trim ring, press firmly on opposite sides of the ring towards the canopy as shown in Figure 19. The tabs will flex out releasing the trim ring from the canopy. 41860-01 02/24/2005

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
© 200
5
Hunter Fan Company
418
6
0
-01
0
2
/
2
4
/200
5
7
wiring the fan
1.
Disconnect the power by turning off the circuit breakers to
the outlet box and associated wall switch location.
2.
Connect the wires as shown in Figure 1
5
. To connect the wires,
twist the bare metal leads together. Place a wire nut over the
intertwined length of wire and twist clockwise until tight.
CAUTION:
B
N:
B
N:
B
N:
B
N:
Be s
e s
e s
e s
e sur
ur
ur
ur
ure n
e n
e n
e n
e no b
o b
o b
o b
o bare w
e w
e w
e w
e wir
ir
ir
ir
ire o
e o
e o
e o
e or w
r w
r w
r w
r wir
ir
ir
ir
ire s
e s
e s
e s
e strands a
s a
s a
s a
s are v
e v
e v
e v
e vis-
ib
ib
ib
ib
ible a
e a
e a
e a
e after m
r m
r m
r m
r makin
in
in
in
ing c
g c
g c
g c
g conn
nn
nn
nn
nnections.
All w
ll w
ll w
ll w
ll wir
ir
ir
ir
irin
in
in
in
ing mu
g mu
g mu
g mu
g must b
t b
t b
t b
t be in a
e in a
e in a
e in a
e in accordance w
e w
e w
e w
e with n
h n
h n
h n
h national a
l a
l a
l a
l and l
d l
d l
d l
d local
electrical c
l c
l c
l c
l codes a
s a
s a
s a
s and A
d A
d A
d A
d ANSI/N
I/N
I/N
I/N
I/NFPA 70. I
A 70. I
A 70. I
A 70. I
A 70. If y
f y
f y
f y
f you a
u a
u a
u a
u are un
e un
e un
e un
e unfamili
ili
ili
ili
iliar
with w
h w
h w
h w
h wir
ir
ir
ir
irin
in
in
in
ing, y
, y
, y
, y
, you s
u s
u s
u s
u shoul
ul
ul
ul
uld u
d u
d u
d u
d use a q
e a q
e a q
e a q
e a quali
li
li
li
lified e
d e
d e
d e
d electrician.
F
installing the canopy
1.
Rotate the fan 180º clockwise from the initial position when
hanging the fan.
The arrows on the hanger ball and on the
ceiling plate should be pointing in the same direction and
should be pointing towards the tab hole on the canopy.
Refer
to Figure 1
6
.
2.
Hook the tab hole over the tab on the ceiling plate as shown in
Figure
17
.
3.
Raise the canopy, be sure the holes in the canopy and the ceil-
ing plate are aligned, and loosely assemble the canopy screws
one at a time.
When all three screws are assembled, securely
tighten all three canopy screws.
Refer to Figure
17
.
installing the canopy trim ring
1.
To easily install the canopy trim ring, locate the two tabs on
the canopy trim ring.
See Figure
18
.
2.
Take both hands and push the canopy trim ring up to the top
of the canopy.
See Figure
18
.
3.
The canopy trim ring will snap and lock into place on the
canopy.
removing the canopy trim ring
1.
Locate the tab indicators, small bumps on top of tabs.
Refer to
Figure
19
.
2.
To remove the canopy trim ring, press firmly on opposite sides
of the ring towards the canopy as shown in Figure
19
.
The tabs
will flex out releasing the trim ring from the canopy.
Tab Hole
and Tab
Canopy
Screw
Power
Wires
in
Ceiling
Black
White
Bare or Green
2 x 4 Brace
Outlet Box
Ceiling Plate
Approved
Connectors
Green Ground Wire from
Hanger Pipe
White
Black
Canopy
Canopy
Trim Ring
Tab
Press Here when
Removing
Press Here when
Removing