Husqvarna AUTOMOWER 450XH EPOS Owner Manual - Page 32

Information and warning messages, Wrong PIN code

Get Husqvarna AUTOMOWER 450XH EPOS PDF manuals and user guides View all Husqvarna AUTOMOWER 450XH EPOS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Message Cause Action No power in charging station Incorrect or damaged power supply. Examine the power supply. If it is necessary, replace the power supply. Power failure. Examine and correct the cause for the power failure of the reference station. The connection between the charging plates on the product and the contact plates on the charging station is not good. Make sure that the charging plates and contact plates are connected. Multiple reference stations There is more than one reference station near the work area. This can cause interference for the product from a different reference station. Speak to your approved servicing dealer if the same problem occurs frequently. 6.3 Information and warning messages The information messages in the table below are shown in the Messages menu in the Automower® Connect app. Speak to your Husqvarna representative if the same message shows frequently. Message Cutting system imbalance Cause The product senses vibrations in the blade disc. Action Examine the blades and screws for damages and wear. Make sure that all blades are correctly installed and that there is only one blade attached in each position on the blade disc. Connectivity problems Problem with the Automower® Connect module. Restart the product. If the connection problem stays, disconnect the product from Automower® Connect and do a new pairing operation. If the problem stays, speak to your local Husqvarna representative. Wrong PIN code An incorrect PIN code has been entered. 5 tries are permitted, and the product is then blocked for a period of time. Enter the correct PIN code. If the PIN code is incorrect, use the link in the app to send the PIN code to your registered e-mail address. If you have not registered the e-mail address, speak to your local Husqvarna representative. Ultrasonic problem GPS navigation problem Temporary electronic or firmware related Restart the product. If the problem stays, problem in the product. speak to your approved servicing dealer. 32 - Troubleshooting 1970 - 001 - 10.10.2022

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Message
Cause
Action
No power in charging station
Incorrect or damaged power supply.
Examine the power supply. If it is neces-
sary, replace the power supply.
Power failure.
Examine and correct the cause for the
power failure of the reference station.
The connection between the charging
plates on the product and the contact
plates on the charging station is not
good.
Make sure that the charging plates and
contact plates are connected.
Multiple reference stations
There is more than one reference station
near the work area. This can cause inter-
ference for the product from a different
reference station.
Speak to your approved servicing dealer
if the same problem occurs frequently.
6.3 Information and warning messages
The information messages in the table below are shown in the
Messages
menu in the Automower
®
Connect app.
Speak to your Husqvarna representative if the same message shows frequently.
Message
Cause
Action
Cutting system imbalance
The product senses vibrations in the
blade disc.
Examine the blades and screws for dam-
ages and wear. Make sure that all blades
are correctly installed and that there is
only one blade attached in each position
on the blade disc.
Connectivity problems
Problem with the Automower
®
Connect
module.
Restart the product. If the connection
problem stays, disconnect the product
from Automower
®
Connect and do a new
pairing operation. If the problem stays,
speak to your local Husqvarna represen-
tative.
Wrong PIN code
An incorrect PIN code has been entered.
5 tries are permitted, and the product is
then blocked for a period of time.
Enter the correct PIN code. If the PIN
code is incorrect, use the link in the
app to send the PIN code to your regis-
tered e-mail address. If you have not reg-
istered the e-mail address, speak to your
local Husqvarna representative.
Ultrasonic problem
Temporary electronic or firmware related
problem in the product.
Restart the product. If the problem stays,
speak to your approved servicing dealer.
GPS navigation problem
32
- Troubleshooting
1970 - 001 - 10.10.2022