Husqvarna K 535i Owner Manual - Page 26

To sharpen the saw blade, To do a check of the trimmer line, Bevel gear

Get Husqvarna K 535i PDF manuals and user guides View all Husqvarna K 535i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

To sharpen the saw blade WARNING: Stop the product and remove the battery. Use protective gloves. • To sharpen the blade correctly, refer to the instructions that come with the blade. • Make sure that the product and blade has sufficient support when you sharpen it. • Adjust the blade set to 1 mm (0.04 in) with the recommended setting tool. Refer to the instructions that come with the blade. • Use a 5.5 mm (7/32 in) round file with a file holder. WARNING: Always discard a blade that is damaged. Do not try to make a bent or twisted blade straight and use it again. To do a check of the trimmer line Only use the recommended trimmer line. See the illustration on the last pages of the manual. 1. Put the cord into the hole on the cover of the product to make sure it follows the recommendation. • Hold the file at an angle of 15°. • Sharpen one tooth of the saw blade to the right and the next tooth to the left, see the illustration. 15˚ Bevel gear The bevel gear is filled to ¾ with grease at the factory. Before use, make sure that the grease level has not changed. Use Husqvarna special grease if it is necessary to fill up. Do not change the grease in the bevel gear. Let servicing personnel do the repair of the bevel gear. Note: Sharpen the edges of the teeth with a flat file if the blade is heavily worn. Continue to sharpen with a round file. • Sharpen all edges equally to keep the blade balanced. 26 609 - 006 - 17.08.2020

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
To sharpen the saw blade
WARNING:
Stop the product and remove
the battery. Use protective gloves.
•
To sharpen the blade correctly, refer to the
instructions that come with the blade.
•
Make sure that the product and blade has sufficient
support when you sharpen it.
•
Use a 5.5 mm (7/32 in) round file with a file holder.
•
Hold the file at an angle of 15°.
•
Sharpen one tooth of the saw blade to the right and
the next tooth to the left, see the illustration.
15˚
Note:
Sharpen the edges of the teeth with a flat file if
the blade is heavily worn. Continue to sharpen with a
round file.
•
Sharpen all edges equally to keep the blade
balanced.
•
Adjust the blade set to 1 mm (0.04 in) with the
recommended setting tool. Refer to the instructions
that come with the blade.
WARNING:
Always discard a blade that is
damaged. Do not try to make a bent or
twisted blade straight and use it again.
To do a check of the trimmer line
Only use the recommended trimmer line. See the
illustration on the last pages of the manual.
1.
Put the cord into the hole on the cover of the product
to make sure it follows the recommendation.
Bevel gear
The bevel gear is filled to ¾ with grease at the factory.
Before use, make sure that the grease level has not
changed. Use Husqvarna special grease if it is
necessary to fill up. Do not change the grease in the
bevel gear. Let servicing personnel do the repair of the
bevel gear.
26
609 - 006 - 17.08.2020