IBM 1352 User Guide - Page 50

Error Message on Display Can't Purge Pswd not enabled Can't Sort Insufficient Memory Printed Message Description This error indicates that MICR mode has not been enabled. This error indicates the printer does not have sufficient memory to sort the Audit Report. Command Decode Error Convert to Esc Error Flash Full Purge and Format Load MICR Toner Decode error &%Sx (where x is the incorrect character) A syntax error was detected in a MICR command. Invalid Convert to Escape Character An error was detected in the User Programmable Escape Character Selection Command. The software tried to specify a NULL or an ampersand as the first Escape Character. This error message indicates that the printer's flash memory is full. The audit trail cannot accept more jobs until more space is available in flash. Before printing a MICR font, the printer checks for MICR toner. If regular toner is present, the printer will stop all printing and display this message. Macro Definition Error Macro Definition Error Macro Definition Error Macro Definition Error Macro Definition Error Macro Transfer Error Macro Transfer Error MICR Definition Error MICR Password Error Invalid decode mode specified Macro ID already in use on SIMM. Print menus to see a list of used ID's. Macro size exceeds available space Non-hexadecimal value received. Non integer value received. Integer string incorrect length Non-integer value received. Password Length Error. The Load Flash Resource Command contained an invalid character specifying the format of the file. Must be either a D or S. The resource number in the Load Flash Resource Command (&%STL...) was over the 32767 list. Flash resource file size specified in the Load Flash Resource Command is too large fro the available space remaining in the flash module. The Load Flash Resource Command contained a non-hexadecimal value in the byte count parameter. The resource number in the Load Flash Resource Command (&%STL...) was not five integers. The Flash Resource Number in the Secure Flash Resource Unlock Command was not five digits in length. The Secure Flash Resource Unlock Command contained a non-integer value. The number of digits in the MICR definition Command is not equal to four, or there is a non-hexadecimal character in the count. Password length is not equal to eight characters. MICR Password Error MICR Password Error Password Match Error Security Lock Not Enabled Error. Password sent does not match the current stored password. Front panel combination feature has been enabled but was not entered before a MICR job was started. Security Lock Error Security Lock Error Integer string incorrect length. Non-integer value received. An error was detected in the Activate/Set Front Panel Combination Lock Command. The combination must be eight digits in length. An error was detected in the Activate/Set Front Panel Combination Lock Command. A character was received in the command that was a non-integer. Secure MICR Printer User's Guide July 2003 Page 46 Action Press Go. Enter MICR mode, then re-attempt the purge. Press Go. The printer may need to be upgraded with more RAM memory to sort; otherwise an unsorted Audit Report may be printed. Check your software for a syntax error in the MICR command that was being used when the error occurred. Check the Command (&%STY...) for errors. Press Go then purge the audit trail. Then either defragment or format flash memory (Utilities Menu). Replace standard toner cartridge with a MICR Toner. Go to proceed. If MICR toner is not available, you must power-off your printer and restart the print job at a later time when MICR toner is available. Check the Command (&%STL...) for syntax errors. Check the Load Flash Resource Command for syntax/numbering errors. Format flash memory to remove all existing resources or upgrade flash memory to a larger module. Check the Command (&%STL...) syntax for errors. Check the command for syntax/ numbering errors. Check the Command (&%STP...) for syntax/numbering errors. Check the Command (&%STP...) for syntax/numbering errors. Check your software for errors in the MICR definition Command. Check the Password Command in your software, it must be eight characters long. Check the Password Command in your software. From the front panel select MICR Menu>Security Lock and enter the correct combination. Press Go to resume the print job. Check the Activate/Set Front Panel Combination Lock Command in your software. Check the Activate/Set Front Panel Combination Lock Command syntax in your software. © Source Technologies All rights reserved