IBM 17011RS Quick Installation Guide - Page 3

DNS

servers

Enter

the

IP

addresses

of

up

to

three

systems

that

will

act

as

DNS

servers.

Enter

no

to

clear

the

list

of

DNS

servers.

dhcp

Enter

yes

if

a

DHCP

server

will

be

used

to

discover

the

system

network

values.

Enter

no

if

a

DHCP

server

will

not

be

used.

If

you

enter

yes

,

the

wizard

takes

you

to

the

finish

parameter.

If

you

enter

no

,

the

wizard

continues

to

prompt

you

for

information

about

the

main

Ethernet

interface

of

the

system.

IP

address

Enter

the

IP

address,

in

x.x.x.x

format.

You

can

also

define

the

netmask

by

typing

its

width

after

the

IP

address.

Note:

For

the

DS300

storage

subsystem,

the

management

interface

must

be

in

a

separate

network

segment

from

your

iSCSI

ports.

netmask

Define

the

size

of

the

netmask.

Any

of

the

common

formats

are

accepted.

Note:

If

you

entered

the

netmask

as

part

of

the

IP

address

in

the

previous

prompt,

this

parameter

is

skipped.

broadcast

address

Enter

the

address

to

be

used

for

broadcasts.

Any

of

the

common

formats

are

accepted.

peer

IP

address

Enter

the

IP

address

for

the

peer

controller,

in

x.x.x

format.

Note:

For

the

DS300

storage

subsystem,

the

management

interface

must

be

in

a

separate

network

segment

from

your

iSCSI

ports.

peer

netmask

Define

the

size

of

the

netmask

for

the

peer

controller.

Any

of

the

common

formats

are

accepted.

peer

broadcast

address

Enter

the

address

to

use

by

the

peer

controller

for

broadcasts.

Any

of

the

common

formats

are

accepted.

finish

Enter

yes

to

apply

the

values

that

you

have

entered,

or

enter

no

to

return

to

the

first

parameter

and

change

the

values

that

you

have

entered.

Note:

If

you

changed

the

management

IP

address

in

step

4

on

page

2,

you

must

open

a

Telnet

session

to

the

new

IP

address.

Installing

the

IBM

ServeRAID

Manager

and

Management

Station

programs

and

adding

a

ServeRAID

agent

To

install

the

IBM

ServeRAID

Manager

and

Management

Station

programs

and

add

a

ServeRAID

agent

for

the

storage

subsystem,

complete

the

following

steps:

1.

Install

the

ServeRAID

Manager

program

on

the

management

station,

using

the

ServeRAID

Application

CD

that

comes

with

the

DS300

or

DS400

storage

subsystem

(see

Chapter

1

of

the

IBM

TotalStorage

DS300

and

DS400

Software

Installation

Guide

for

instructions).

2.

Install

the

Management

Station

program

on

the

management

station

(see

Chapter

1

of

the

Software

Installation

Guide

for

instructions).

3

Section	Page
IBM TotalStorage DS300 and DS400 Quick Installation Guide	1
Obtaining the documentation from the IBM Support Web site	1
Installing the hardware	1
Setting the controller defaults	2
Installing the IBM ServeRAID Manager and Management Station programs and adding a ServeRAID agent	3
Installing the controller firmware	4
Setting IP addresses for DS300 iSCSI ports	4
Configuring the RAID device in ServeRAID Manager	4
Getting help and technical assistance	6
Before you call	6
Using the documentation	6
Getting help and information from the World Wide Web	6
Software service and support	7
Hardware service and support	7
Notices	8
Trademarks	8
Important notes	9
Product recycling and disposal	9
Battery return program	10
Electronic emission notices	11
Federal Communications Commission (FCC) statement	11
Industry Canada Class A emission compliance statement	11
Australia and New Zealand Class A statement	11
United Kingdom telecommunications safety requirement	11
European Union EMC Directive conformance statement	11
Taiwanese Class A warning statement	12
Chinese Class A warning statement	12

IBM 17011RS Quick Installation Guide - Page 3

Installing, ServeRAID, Manager, Management, Station, programs, adding, agent

Page 3 highlights