IBM 2019A1X Installation Guide - Page 32

Ethernet connection (CLI), User's Guide, User's, Guide, Command-Line Interface Guide

Get IBM 2019A1X - Bladecenter Advanced Management Module PDF manuals and user guides
UPC - 883436070805
View all IBM 2019A1X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Ethernet connection (CLI) After you connect the Ethernet cable from the management module to the client computer, complete the following steps: 1. Make sure that the subnet of the client computer is set to the same value as the default management-module subnet (255.255.255.0). 2. Open a console window and log in to the default management-module IP address (192.168.70.125). 3. Enter the default user name, USERID, and the default password, PASSW0RD (note the number zero, not the letter O, in PASSW0RD), to start the remote session. After you connect the client computer to the management module for the first time, perform initial configuration of the BladeCenter unit. See the management-module User's Guide for configuration instructions. Serial connection (CLI) After you connect the serial cable from the management module to the client computer, complete the following steps: 1. Make sure that the serial port of the client computer is set to the following settings: v Baud rate = 57600 v Parity = none v Stop bits = 1 2. Open a terminal emulator window and establish a connection to the management-module serial port. 3. Enter the default user name, USERID, and the default password, PASSW0RD (note the number zero, not the letter O, in PASSW0RD), to start the remote session. After you connect to the management module for the first time, perform initial configuration of the BladeCenter unit. See the management-module User's Guide for GUI-configuration instructions or the management-module Command-Line Interface Guide for CLI-configuration instructions. 22 BladeCenter Advanced Management Module: Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Ethernet connection (CLI)
After you connect the Ethernet cable from the management module to the
client computer, complete the following steps:
1.
Make sure that the subnet of the client computer is set to the same value as
the default management-module subnet (255.255.255.0).
2.
Open a console window and log in to the default management-module IP
address (192.168.70.125).
3.
Enter the default user name, USERID, and the default password,
PASSW0RD (note the number zero, not the letter O, in PASSW0RD), to start
the remote session.
After you connect the client computer to the management module for the first
time, perform initial configuration of the BladeCenter unit. See the
management-module
User’s Guide
for configuration instructions.
Serial connection (CLI)
After you connect the serial cable from the management module to the client
computer, complete the following steps:
1.
Make sure that the serial port of the client computer is set to the following
settings:
v
Baud rate = 57600
v
Parity = none
v
Stop bits = 1
2.
Open a terminal emulator window and establish a connection to the
management-module serial port.
3.
Enter the default user name, USERID, and the default password,
PASSW0RD (note the number zero, not the letter O, in PASSW0RD), to start
the remote session.
After you connect to the management module for the first time, perform initial
configuration of the BladeCenter unit. See the management-module
User’s
Guide
for GUI-configuration instructions or the management-module
Command-Line Interface Guide
for CLI-configuration instructions.
22
BladeCenter Advanced Management Module: Installation Guide