IBM 4810 33H Service Guide - Page 32

Removing, planar

Get IBM 4810 33H PDF manuals and user guides View all IBM 4810 33H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Removing the planar Updated May 20, 2008 Figure 2-10. Removing the planar. (View after the riser card assembly has been removed) 1. Open the unit (see "Opening the unit" on page 2-2). 2. Lift the riser card assembly out of the 4810. 3. Disconnect all cables that are attached to the planar. 4. Remove the hard-disk drive (see "Removing the hard-disk drive" on page 2-5). 5. Remove the memory (see "Removing memory" on page 2-7). 6. Remove the heat sink and fan assembly (see "Removing the heat sink and fan assembly" on page 2-8). 7. Remove the CPU (see "Removing the CPU" on page 2-9). 8. Remove the screws beside the printer port and serial port B on the back cover of the 4810. 9. Remove the six hex screws on the planar. 10. Slide the planar toward the front of the 4810, then lift the planar out of the 4810. 11. To replace the planar, reverse this procedure. 2-14 SurePOS Installation and Service

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Removing
the
planar
1.
Open
the
unit
(see
“Opening
the
unit”
on
page
2-2).
2.
Lift
the
riser
card
assembly
out
of
the
4810.
3.
Disconnect
all
cables
that
are
attached
to
the
planar.
4.
Remove
the
hard-disk
drive
(see
“Removing
the
hard-disk
drive”
on
page
2-5).
5.
Remove
the
memory
(see
“Removing
memory”
on
page
2-7).
6.
Remove
the
heat
sink
and
fan
assembly
(see
“Removing
the
heat
sink
and
fan
assembly”
on
page
2-8).
7.
Remove
the
CPU
(see
“Removing
the
CPU”
on
page
2-9).
8.
Remove
the
screws
beside
the
printer
port
and
serial
port
B
on
the
back
cover
of
the
4810.
9.
Remove
the
six
hex
screws
on
the
planar.
10.
Slide
the
planar
toward
the
front
of
the
4810,
then
lift
the
planar
out
of
the
4810.
11.
To
replace
the
planar,
reverse
this
procedure.
Figure
2-10.
Removing
the
planar.
(View
after
the
riser
card
assembly
has
been
removed)
Updated
May
20,
2008
2-14
SurePOS
Installation
and
Service