IBM 4910-33S Installation Guide - Page 27

Installing Windows Embedded for Point Of Service on SurePOS 300 (Models E3H, 33H and 330)

Get IBM 4910-33S PDF manuals and user guides View all IBM 4910-33S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 5. Installing Windows Embedded for Point Of Service on SurePOS 300 (Models E3H, 33H and 330) If you are using the installation CD to install Windows® Embedded for Point Of Service (WEPOS) on IBM Retail Store Solutions hardware, there are special instructions for some of the system units. This document provides those instructions to enable you to be successful in building an operational WEPOS image for your machine. Note: These special procedures apply only to WEPOS version 1.0 and 1.1. The WEPOS Version 1.1 Upgrade and beyond (Windows Embedded POSReady) do not require any modifications to the WEPOS installation CDs. These instructions are necessary because one or more drivers associated with the hard drive on the SurePOS 300 (Models E3H, 33H and 330) are not contained in the original WEPOS installation CDs from Microsoft. To use the following instructions there must be one partition for the CD-ROM drive and it must be identified as D:. These instructions assume you have access to the WEPOS OEM Preinstallation Kit (OPK) CDs from Microsoft. and the necessary tools described in this document. The OPK is available through the Microsoft distribution channel. A trial version of the WEPOS OPK could also be ordered directly from Microsoft using the following URL: http://www.microsoft.com/windows/embedded/eval/trial.mspx Please, note that per the Microsoft agreement, IBM RSS cannot provide this package. You must have access to the necessary tools described in this document to modify and recreate the WEPOS installation CDs such as oscdimg.exe. These tools are available from Microsoft on the Tools CD that comes with the full version of the XP Pro or the WEPOS OEM OPK (the tools are NOT included in the trial version of the WEPOS OPK). SurePOS 300 (Models E3H, 33H and 330) require special handling to successfully install WEPOS because the drivers for the Serial ATA hard drive are not on the WEPOS OPK. The following instructions describe how to add this driver to the WEPOS installation OPK. 1. Adding Driver to Run the WEPOS Install CD © Copyright IBM Corp. 2005 Note: Microsoft has a knowledgebase article titled "How to add unsupported or updated third-party mass storage drivers to a customized WinPE CD". This article is the basis of the instructions in this section and can be found at the following URL: http://support.microsoft.com/ default.aspx?scid=kb;en-us;319214 This section describes how to add the needed driver to the WEPOS installation CD in order for the installation process to see and recognize the SATA hard drive. The WEPOS installation CD is based on Win PE. a. Copy the contents of the WEPOS installation CD to a work space. Usually the work space is on a workstation. For example, assume you have created a subdirectory named WEPOS_INSTALL on your C: drive. Copy all the files and subdirectories on the CD to this space by entering: xcopy d:\*.* c:\WEPOS_INSTALL /e on a command line or using the Windows graphical user interface you can select the contents of the CD and copy them to the target subdirectory. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Chapter 5. Installing Windows Embedded for Point Of Service
on SurePOS 300 (Models E3H, 33H and 330)
If you are using the installation CD to install Windows
®
Embedded for Point Of
Service (WEPOS) on IBM Retail Store Solutions hardware, there are special
instructions for some of the system units. This document provides those instructions
to enable you to be successful in building an operational WEPOS image for your
machine.
Note:
These special procedures apply only to WEPOS version 1.0 and 1.1. The
WEPOS Version 1.1 Upgrade and beyond (Windows Embedded POSReady)
do not require any modifications to the WEPOS installation CDs.
These instructions are necessary because one or more drivers associated with the
hard drive on the SurePOS 300 (Models E3H, 33H and 330) are not contained in
the original WEPOS installation CDs from Microsoft.
To use the following instructions there must be one partition for the CD-ROM drive
and it must be identified as D:.
These instructions assume you have access to the WEPOS OEM Preinstallation Kit
(OPK) CDs from Microsoft. and the necessary tools described in this document.
The OPK is available through the Microsoft distribution channel. A trial version of
the WEPOS OPK could also be ordered directly from Microsoft using the following
per the Microsoft agreement, IBM RSS cannot provide this package.
You must have access to the necessary tools described in this document to modify
and recreate the WEPOS installation CDs such as oscdimg.exe. These tools are
available from Microsoft on the Tools CD that comes with the full version of the XP
Pro or the WEPOS OEM OPK (the tools are NOT included in the trial version of the
WEPOS OPK).
SurePOS 300 (Models E3H, 33H and 330) require special handling to successfully
install WEPOS because the drivers for the Serial ATA hard drive are not on the
WEPOS OPK. The following instructions describe how to add this driver to the
WEPOS installation OPK.
1.
Adding Driver to Run the WEPOS Install CD
Note:
Microsoft has a knowledgebase article titled “How to add unsupported or
updated third-party mass storage drivers to a customized WinPE CD”.
This article is the basis of the instructions in this section and can be
found at the following URL: http://support.microsoft.com/
default.aspx?scid=kb;en-us;319214
This section describes how to add the needed driver to the WEPOS installation
CD in order for the installation process to see and recognize the SATA hard
drive. The WEPOS installation CD is based on Win PE.
a.
Copy the contents of the WEPOS installation CD to a work space. Usually
the work space is on a workstation. For example, assume you have created
a subdirectory named WEPOS_INSTALL on your C: drive. Copy all the files
and subdirectories on the CD to this space by entering: xcopy d:\*.*
c:\WEPOS_INSTALL /e on a command line or using the Windows graphical
user interface you can select the contents of the CD and copy them to the
target subdirectory.
© Copyright IBM Corp. 2005
13