IBM 8676 Installation Guide - Page 20

Removing the cover and bezel, Attention

Get IBM 8676 - Eserver xSeries 335 PDF manuals and user guides
UPC - 087944770107
View all IBM 8676 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

v Take additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity. Removing the cover and bezel Complete the following steps to remove the cover and bezel: 1. Read the safety information beginning on page v, and "Installation guidelines" on page 7. 2. Turn off the server and all attached peripheral devices. Disconnect all power cords; then, disconnect all external signal cables from the server. 3. Lift the cover release latch. The cover slides to the rear approximately 13 mm (0.5 inch). Captive screws Bezel retention tabs USB option tray Bezel retention tabs Retention clip 4. Slide the cover back, and lift the cover off the server. Attention: To ensure adequate cooling and airflow, do not operate the server with the cover removed. Operating the server with the cover removed might damage server components. 5. Press in on the USB option tray (below hard disk drive bay 1) to release it and slide the tray out until it stops; then, press the retention clip at the bottom rear of the tray and remove the tray from the server. Note: You need to remove the USB option tray and the bezel only if you are installing a non-hot-swap hard disk drive. It is not necessary if you are installing other options in the server. 6. Press on the bezel retention tabs on the top, right side and bottom of the server, and pull the bezel directly away from the server. 8 IBM xSeries 335 Type 8676: Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
v
Take additional care when handling devices during cold weather. Heating reduces
indoor humidity and increases static electricity.
Removing the cover and bezel
Complete the following steps to remove the cover and bezel:
1.
Read the safety information beginning on page v, and “Installation guidelines” on
page 7.
2.
Turn off the server and all attached peripheral devices. Disconnect all power
cords; then, disconnect all external signal cables from the server.
3.
Lift the cover release latch. The cover slides to the rear approximately 13 mm
(0.5 inch).
Bezel retention
tabs
Bezel
retention
tabs
USB option tray
Captive screws
Retention
clip
4.
Slide the cover back, and lift the cover off the server.
Attention:
To ensure adequate cooling and airflow, do not operate the server
with the cover removed. Operating the server with the cover removed might
damage server components.
5.
Press in on the USB option tray (below hard disk drive bay 1) to release it and
slide the tray out until it stops; then, press the retention clip at the bottom rear
of the tray and remove the tray from the server.
Note:
You need to remove the USB option tray and the bezel only if you are
installing a non-hot-swap hard disk drive. It is not necessary if you are
installing other options in the server.
6.
Press on the bezel retention tabs on the top, right side and bottom of the server,
and pull the bezel directly away from the server.
8
IBM xSeries 335 Type 8676: Installation Guide