Icom IP501H Instruction Manual - Page 29

Searching network operator, User select, Network Selection

Get Icom IP501H PDF manuals and user guides View all Icom IP501H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3 ADVANCED OPERATION ■ Searching network operator The Network Search function search the available operator. 1. Setting the Network Search function enable 1. While holding down [FUNC], turn ON the power. ••Enter the Set mode. 2. Release [FUNC] when "SET" is displayed. 3. Push [FUNC] or [Address] several times to select "Network Selection." 4. Push to select "User Select." 5. Push [CLR/LOCK]. ••Exits the Set mode. [Address] [FUNC] [CLR/LOCK SET LOG - - - SET Network Selection User select 2. Starting a Network Search 1. Push [FUNC] several times to select "Network Search." 2. Push [Call history] to start a search. ••Network search starts. ••The search result will be displayed in few minutes. LSearch may take a time, depending on the environment. LIf "Timeout" is displayed, try a different location. 3. Push to select an operator. ••Select "Search" if you start the search again. 4. Push [Call history] to set the selected operator. ••"Configured" is displayed. [Call history] [FUNC SET LOG - - - Network Search Search Network Search ABCD 12345 (Example) Network Search Configured NOTE: ••This function may not work, depending on the country of use or service provider setting. ••The transceiver may not connect to the operator in the search result, depending on the communication service contract. (For example: Roaming is not supported.) 3-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
3
ADVANCED OPERATION
3-14
1. Setting the Network Search function enable
1.
While holding down [FUNC], turn ON the power.
•
Enter the Set mode.
2.
Release [FUNC] when “SET” is displayed.
3.
Push [FUNC] or [Address] several times to select “Network
Selection.”
4.
Push [▲]/[▼] to select “User Select.”
5. Push [CLR/LOCK].
•
Exits the Set mode.
2. Starting a Network Search
1.
Push [FUNC] several times to select “Network Search.”
2.
Push [Call history] to start a search.
•
Network search starts.
•
The search result will be displayed in few minutes.
L
Search may take a time, depending on the environment.
L
If “Timeout” is displayed, try a different location.
3.
Push [▲]/[▼] to select an operator.
•
Select “Search” if you start the search again.
4.
Push [Call history] to set the selected operator.
•
“Configured” is displayed.
■ Searching network operator
The Network Search function search the available operator.
– – –
LOG
SET
– – –
LOG
SET
[FUNC]
[CLR/LOCK]
[▲]/[▼]
(Example)
User select
Network Selection
SET
[FUNC]
[▲]/[▼]
[Call history]
Search
Network Search
ABCD
12345
Network Search
Configured
Network Search
[Address]
NOTE:
•
This function may not work, depending on the country of use or service provider setting.
•
The transceiver may not connect to the operator in the search result, depending on the communication service contract.
(For example: Roaming is not supported.)