Image Fitness 3.8 English Manual - Page 14

Adjusting the Weight Bench

Get Image Fitness 3.8 PDF manuals and user guides View all Image Fitness 3.8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Adjusting the Weight Bench This section explains how the weight bench is adjusted. See the included exercise guide for important information about how to perform a variety of exercises and how to get the greatest benefit from your exercise program. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. USING THE LOCKING BAR AND SAFETY SPOTTERS Before starting an exercise, position the barbell and the 1 Safety Spotters (23, 24) in the correct position for that exercise. To do this, stand in front of the cage and grip the Locking 1 Bar (34) with both hands. Turn the Locking Bar until the two hooks disengage the slots in the Uprights (1). Move 31 the Locking Bar to a new position and turn the Locking Bar until the hooks engage the slots in the Uprights. 23 Note: Always start an exercise with the barbell posi- 34 tioned at the lowest point to which it will move during the exercise. 32 Position both Safety Spotters (23, 24) directly under the Weight Gliders (31, 32). 24 USING THE SAFETY SPOTTERS To move a Safety Spotter (23, 24 [not shown]) to a new position, grip the handle on one side of the Spotter Hook (61, 62 [not shown]) and pull the Spotter Hook out of the slot in the Upright (1). Raise or lower the Safety Spotter to a new position and turn the Spotter Hook until it engages one of the slots in the Upright. WARNING: Always set both Safety Spotters at the 23 same height. 1 61 Handle ATTACHING WEIGHTS TO THE BARBELL To use the Barbell (35), slide the desired amount of weight (not included) onto each end of the Barbell. Secure the weights with the Large Weight Clips (13). 33 Note: To use standard weights, the Weight Adapters (33) should be removed from the Barbell (35). Attach weights 35 to the Barbell with the Small Weight Clips (not shown). 13 WARNING: Do not place more than 260 pounds on the barbell. Always secure the weights with weight clips when they are on the barbell. Always place the same amount of weight on each side of the barbell. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
14
This section explains how the weight bench is adjusted. See the included exercise guide for important informa-
tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
Adjusting the Weight Bench
USING THE SAFETY SPOTTERS
To move a Safety Spotter (23, 24 [not shown]) to a new
position, grip the handle on one side of the Spotter Hook
(61, 62 [not shown]) and pull the Spotter Hook out of the
slot in the Upright (1). Raise or lower the Safety Spotter to
a new position and turn the Spotter Hook until it engages
one of the slots in the Upright.
23
61
1
Handle
USING THE LOCKING BAR AND SAFETY SPOTTERS
Before starting an exercise, position the barbell and the
Safety Spotters (23, 24) in the correct position for that
exercise.
To do this, stand in front of the cage and grip the Locking
Bar (34) with both hands.Turn the Locking Bar until the
two hooks disengage the slots in the Uprights (1). Move
the Locking Bar to a new position and turn the Locking
Bar until the hooks engage the slots in the Uprights.
Note: Always start an exercise with the barbell posi-
tioned at the lowest point to which it will move during
the exercise.
Position both Safety Spotters (23, 24) directly under the
Weight Gliders (31, 32).
24
32
31
23
34
1
1
ATTACHING WEIGHTS TO THE BARBELL
To use the Barbell (35), slide the desired amount of
weight (not included) onto each end of the Barbell.
Secure the weights with the Large Weight Clips (13).
Note:To use standard weights, the Weight Adapters (33)
should be removed from the Barbell (35). Attach weights
to the Barbell with the Small Weight Clips (not shown).
35
33
13
WARNING: Always set both Safety Spotters at the
same height.
WARNING: Do not place more than 260 pounds on
the barbell. Always secure the weights with weight
clips when they are on the barbell. Always place
the same amount of weight on each side of the bar-
bell.