Intel BLKD201GLYL Product Specification - Page 45

BIOS Setup Configuration Jumper Block

Get Intel BLKD201GLYL PDF manuals and user guides View all Intel BLKD201GLYL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Technical Reference CAUTION Do not place jumpers on this block in any configuration other than the one described in Table 19. Other jumper configurations are not supported and could damage the Desktop Board. Table 19. Front Panel Audio Header/Jumper Block Jumper Setting 5 and 6 9 and 10 Configuration Audio line out and mic in signals are routed to the back panel audio connectors. The back panel audio connectors are shown in Figure 6 on page 37. No jumpers installed Table 12 on page 39 lists the names of the signals available on this connector when no jumpers are installed. # INTEGRATOR'S NOTE When the jumpers are removed and this connector is used for front panel audio, the back panel audio line out and mic in connectors are disabled. 2.3.2 BIOS Setup Configuration Jumper Block This 3-pin jumper block determines the BIOS Setup program's mode. Table 20 describes the jumper settings for the three modes: normal, configure, and recovery. When the jumper is set to configuration mode and the computer is powered-up, the BIOS compares the processor version and the microcode version in the BIOS and reports if the two match. Table 20. BIOS Setup Configuration Jumper Settings Function/Mode Jumper Setting Configuration Normal 1-2 The BIOS uses current configuration information and passwords for booting. Configure 2-3 321 After the POST runs, Setup runs automatically. The maintenance menu is displayed. Recovery 321 None 321 The BIOS attempts to recover the BIOS configuration. A recovery diskette is required. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Technical Reference
45
CAUTION
Do not place jumpers on this block in any configuration other than the one described
in Table 19.
Other jumper configurations are not supported and could damage the
Desktop Board.
Table 19. Front Panel Audio Header/Jumper Block
Jumper Setting
Configuration
5 and 6
9 and 10
Audio line out and mic in signals are routed to the back panel audio
connectors.
The back panel audio connectors are shown in Figure 6 on
page 37.
No jumpers
installed
Table 12 on page 39 lists the names of the signals available on this
connector when no jumpers are installed.
INTEGRATOR’S NOTE
When the jumpers are removed and this connector is used for front panel audio, the
back panel audio line out and mic in connectors are disabled.
2.3.2
BIOS Setup Configuration Jumper Block
This 3-pin jumper block determines the BIOS Setup program’s mode.
Table 20
describes the jumper settings for the three modes:
normal, configure, and recovery.
When the jumper is set to configuration mode and the computer is powered-up, the
BIOS compares the processor version and the microcode version in the BIOS and
reports if the two match.
Table 20. BIOS Setup Configuration Jumper Settings
Function/Mode Jumper Setting
Configuration
Normal
1-2
321
The BIOS uses current configuration information and
passwords for booting.
Configure
2-3
321
After the POST runs, Setup runs automatically.
The
maintenance menu is displayed.
Recovery
None
321
The BIOS attempts to recover the BIOS configuration.
A
recovery diskette is required.