Intel D850MD Product Guide - Page 33

Installing the AGP Card Retention Mechanism

Get Intel D850MD - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858147149
View all Intel D850MD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Installing and Replacing Desktop Board Components The AGP card RM (see Figure 15) encloses the board's AGP connector and stabilizes the AGP card. Place the board (component side up) on a flat, supportive surface. Follow the steps outlined below to attach the AGP card RM (A) to the AGP connector (B): 1. Locate the AGP connector on the board as shown below. Note that the board's silkscreen (C) indicates the correct final position of the lever (D) on the AGP card RM. A D E C B OM11842 Figure 15. Installing the AGP Card Retention Mechanism 2. Position the AGP card RM over the AGP connector as shown below. OM10111 3. Push the lever end of the AGP card RM in the direction of the arrow until the two rearmost tabs (E) spread over the end of the AGP connector. OM10180 4. Push the free end of the AGP card RM over the other end of the AGP connector and press down evenly on both ends of the RM until all four tabs click underneath the AGP connector. do To avoid damaging the board, not apply unnecessary pressure. OM10181 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Installing and Replacing Desktop Board Components
33
The AGP card RM (see Figure 15) encloses the board
’
s AGP connector and stabilizes the AGP
card.
Place the board (component side up) on a flat, supportive surface.
Follow the steps outlined
below to attach the AGP card RM (A) to the AGP connector (B):
1.
Locate the AGP connector on the board as shown below.
Note that the board
’
s silkscreen (C)
indicates the correct final position of the lever (D) on the AGP card RM.
OM11842
C
B
A
E
D
Figure 15.
Installing the AGP Card Retention Mechanism
2.
Position the AGP card RM over the AGP connector as shown below.
OM10111
3.
Push the lever end of the AGP card RM in the direction of the arrow until the two rearmost
tabs (E) spread over the end of the AGP connector.
OM10180
4.
Push the free end of the AGP card RM over the other end of the AGP connector and press
down evenly on both ends of the RM until all four tabs click underneath the AGP connector.
do To avoid damaging the board, not apply unnecessary pressure.
OM10181