Intel D945GCPE Product Guide - Page 55

A Error Messages

Get Intel D945GCPE - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858195195
View all Intel D945GCPE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

A Error Messages Desktop Board D945GCPE reports POST errors by displaying an error message on the monitor. BIOS Error Messages When a recoverable error occurs during the POST, the BIOS displays an error message describing the problem. Table 12 gives an explanation of the BIOS error messages. Table 12. BIOS Error Messages Error Message Explanation PROCESSOR_THERMAL_TRIP_ERROR Processor was previously shutdown due to a thermal event (overheating). MULTI_BIT_ECC_ERROR The firmware has detected that a Multi-Bit ECC Error occurred. SINGLE_BIT_ECC_ERROR CMOS_BATTERY_ERROR CMOS_CHECKSUM_ERROR The firmware has detected that a Single-Bit ECC Error occurred. The firmware has detected that a CMOS battery failure occurred. The firmware has detected that a CMOS Checksum Error occurred. CMOS_TIMER_ERROR The firmware has detected that the system date/time has not been set. MEMORY_SIZE_DECREASE_ERROR The firmware has detected that the system memory has decreased. INTRUDER_DETECTION_ERROR The system chassis was opened. SPD_TOLER_ERROR SERIAL PRESENCE DETECT (SPD) device data missing or inconclusive. Properly programmed SPD device data is required for reliable operation. DDR2-533 MHz memory assumed at slowest timings. MEM_OPTIMAL_ERROR The installed amount of memory in Channel A is not equal to the amount of memory in Channel B. Maximum memory performance is achieved with equal amounts of memory installed in each channel. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
55
A Error Messages
Desktop Board D945GCPE reports POST errors by displaying an error message on the
monitor.
BIOS Error Messages
When a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem.
Table 12 gives an explanation of the BIOS error messages.
Table 12. BIOS Error Messages
Error Message
Explanation
PROCESSOR_THERMAL_TRIP_ERROR
Processor was previously shutdown due to a thermal event
(overheating).
MULTI_BIT_ECC_ERROR
The firmware has detected that a Multi-Bit ECC Error occurred.
SINGLE_BIT_ECC_ERROR
The firmware has detected that a Single-Bit ECC Error occurred.
CMOS_BATTERY_ERROR
The firmware has detected that a CMOS battery failure occurred.
CMOS_CHECKSUM_ERROR
The firmware has detected that a CMOS Checksum Error
occurred.
CMOS_TIMER_ERROR
The firmware has detected that the system date/time has not
been set.
MEMORY_SIZE_DECREASE_ERROR
The firmware has detected that the system memory has
decreased.
INTRUDER_DETECTION_ERROR
The system chassis was opened.
SPD_TOLER_ERROR
SERIAL PRESENCE DETECT (SPD) device data missing or
inconclusive.
Properly programmed SPD device data is required
for reliable operation.
DDR2-533 MHz memory assumed at
slowest timings.
MEM_OPTIMAL_ERROR
The installed amount of memory in Channel A is not equal to the
amount of memory in Channel B.
Maximum memory
performance is achieved with equal amounts of memory
installed in each channel.