Intel SR1520ML User Guide - Page 114

Drive Activity Light Does Not Light, CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light,

Get Intel SR1520ML - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858197403
View all Intel SR1520ML manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

• Are the power supply cables properly connected to the server board? • Are there any shorted wires caused by pinched-cables or have power connector plugs been forced into power connector sockets the wrong way? Drive Activity Light Does Not Light Check the following: • Are the drive's power and signal cables properly installed? • Are all relevant switches and jumpers on the drive set correctly? • Is the drive properly configured? • Is the drive activity light always on? If so, the signal cable may be plugged in incorrectly. CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light Check the following: • Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed? • Are all relevant switches and jumpers on the drive set correctly? • Is the drive properly configured? Cannot Connect to a Server • Make sure the network cable is securely attached to the correct connector at the system back panel. • Try a different network cable. • Make sure you are using the correct and the current drivers. See "Server System References" on page xix for a link to the current drivers. • Make sure the driver is loaded and the protocols are bound. • Make sure the hub port is configured for the same duplex mode as the network controller. • Make sure the correct networking software is installed. • If you are directly connecting two servers (without a hub), you will need a crossover cable. • Check the network controller LEDs next to the NIC connectors. 94 Intel® Server System SR1520ML User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
94
Intel
®
Server System SR1520ML User’s Guide
•
Are the power supply cables properly connected to the server board?
•
Are there any shorted wires caused by pinched-cables or have power connector
plugs been forced into power connector sockets the wrong way?
Drive Activity Light Does Not Light
Check the following:
•
Are the drive's power and signal cables properly installed?
•
Are all relevant switches and jumpers on the drive set correctly?
•
Is the drive properly configured?
•
Is the drive activity light always on? If so, the signal cable may be plugged in
incorrectly.
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light
Check the following:
•
Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed?
•
Are all relevant switches and jumpers on the drive set correctly?
•
Is the drive properly configured?
Cannot Connect to a Server
•
Make sure the network cable is securely attached to the correct connector at the
system back panel.
•
Try a different network cable.
•
Make sure you are using the correct and the current drivers. See
“Server System
References” on page xix
for a link to the current drivers.
•
Make sure the driver is loaded and the protocols are bound.
•
Make sure the hub port is configured for the same duplex mode as the network
controller.
•
Make sure the correct networking software is installed.
•
If you are directly connecting two servers (without a hub), you will need a crossover
cable.
•
Check the network controller LEDs next to the NIC connectors.