Home » Intel Manuals » Desktops » Intel SR1530HCL » Manual Viewer

Intel SR1530HCL Product Specification - Page 26

Optical Drive Support

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Peripheral and Hard Drive Support Intel® Server Systems SR1530CL/SR1530HCL/SR1530HCS and SR1530CLR/SR1530HCLR/SR1530HCLSR Figure 15. Drive Bays - SR1530HCL/SR1530HCLR (SATA) and SR1530HCLS/SR1530HCLSR (SAS) A Slimline optical drive bay B Hot Swap Hard drive bay 4.1 Optical Drive Support The system provides a slimline drive bay that can be configured for an IDE optical CD-ROM, or a DVD/CDR drive. Drives are mounted on a tool-less tray which allows for easy installation into and removal from the system. The slimline devices are not hot-swappable. 4.1.1 Optical Drive Support The systems support a slimline IDE optical drive. The drive is mounted onto a tool-less drive tray and is connected to an interposer card attached to the tray. The drive assembly is then inserted in to the slimline drive bay. A 44-pin ribbon cable is used to connect the drive assembly to a matching IDE connector on the server board. 18 Revision 2.2 Intel order number D71005-005

Section	Page
1. Introduction	9
1.1 System Views	9
1.2 System Dimensions	10
1.3 System Components	11
1.4 System Boards	13
1.5 Hard Drive and Peripheral Bays	13
1.6 Power Sub-System	15
1.7 System Cooling	15
1.8 Rack and Cabinet Mounting Options	15
2. Power Sub-System	16
2.1 Mechanical Overview	16
2.2 Output Connectors	17
2.2.1 P1 – Main Power Connector	17
2.2.2 P2 – Processor Power Connector	18
2.2.3 P3 – Baseboard Signal Connector	18
2.2.4 P4 and P5 – SATA Hard Drive Power Connectors	18
2.2.5 P6 – CD Power Connector	19
2.2.6 P7 – HSBP Power Connector	19
2.3 Efficiency	19
2.4 AC Input Voltage Requirement	19
2.5 Protection Circuits	20
2.5.1 Over-current Protection (OCP)	20
2.5.2 Over-voltage Protection (OVP)	20
2.5.3 Over-temperature Protection (OTP)	21
2.6 AC Power Cord Specification Requirements	21
3. Cooling Sub-System	22
3.1 Power Supply Fans	23
3.2 Processor Air Duct and Air Baffle	23
4. Peripheral and Hard Drive Support	25
4.1 Optical Drive Support	26
4.1.1 Optical Drive Support	26
4.2 Hard Disk Drive Support	27
4.2.1 Hot-Swap Hard Disk Drive Trays	27
4.2.2 Drive Blanks	28
4.2.3 System Fan Connectors	29
5. Front Control Panel	30
5.1.1 Power/Sleep LED	32
5.1.2 System Status LED	32
5.1.3 Drive Activity LED	33
6. PCI Riser Cards and Assembly	34
7. Backplane Board	35
7.1.1 Hard Drive Activity LED	37
8. Supported Intel® Server Boards	38
8.1 Intel® Server Board S5000VCL Feature Set	38
9. Environmental and Regulatory Specifications	39
9.1 System Level Environmental Limits	39
9.2 Serviceability and Availability	39
9.3 Replacing the CMOS Battery	40
9.4 Product Regulatory Compliance	41
9.5 Use of Specified Regulated Components	41
9.6 Electromagnetic Compatibility Notices	43
9.6.1 USA	43
9.6.2 FCC Verification Statement	44
9.6.3 ICES-003 (Canada)	44
9.6.4 Europe (CE Declaration of Conformity)	44
9.6.5 Japan EMC Compatibility	44
9.6.6 BSMI (Taiwan)	45
9.6.7 RRL (Korea)	45
9.7 Product Ecology Compliance	46
9.8 Other Markings	48
Appendix A: Integration and Usage Tips	49
Appendix B: POST Code Diagnostic LED Decoder	50
Appendix C: POST Error Beep Codes	54
Glossary	54

Match case Limit results 1 per page

Peripheral and Hard Drive Support

Intel® Server Systems SR1530CL/SR1530HCL/SR1530HCS

and SR1530CLR/SR1530HCLR/SR1530HCLSR

Revision 2.2

Intel order number D71005-005

Figure 15. Drive Bays - SR1530HCL/SR1530HCLR (SATA) and SR1530HCLS/SR1530HCLSR (SAS)

Slimline optical drive bay

Hot Swap Hard drive bay

4.1

Optical Drive Support

The system provides a slimline drive bay that can be configured for an IDE optical CD-ROM, or

a DVD/CDR drive. Drives are mounted on a tool-less tray which allows for easy installation into

and removal from the system. The slimline devices are not hot-swappable.

4.1.1

Optical Drive Support

The systems support a slimline IDE optical drive. The drive is mounted onto a tool-less drive

tray and is connected to an interposer card attached to the tray. The drive assembly is then

inserted in to the slimline drive bay. A 44-pin ribbon cable is used to connect the drive assembly

to a matching IDE connector on the server board.