Home » Intel Manuals » Desktops » Intel SR1530HCL » Manual Viewer

Intel SR1530HCL Product Specification - Page 49

Appendix A: Integration and Usage Tips, System Management Software

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Intel® Server Systems SR1530CL/SR1530HCL/SR1530HCS and SR1530CLR/SR1530HCLR/SR1530HCLSR Appendix A: Integration and Usage Tips Appendix A: Integration and Usage Tips This section provides a list of useful information that is unique to the Intel® Server Systems SR1530CL/SR1530HCL/SR1530HCLS and should be kept in mind while integrating and server system. ƒ Only low-profile (1.2 inch or 30.48 mm) FBDIMMs can be used in the server systems. ƒ Processor fans are not needed and are not supported. The system fan blowers and power supply fans provide the necessary cooling needed for the system. Using a processor fan in these systems may cause Intel® System Management Software to incorrectly monitor the system fans. ƒ The air duct must be used to maintain system thermals. ƒ System fan blowers are not hot swappable ƒ A screw on the front edge of the top cover is required when the unit is installed in a useraccessible environment. ƒ The FRUSDR utility must be run to load the proper sensor data records for the server system onto the server board. ƒ Make sure the latest system software is loaded. This includes system BIOS, FRUSDR, and BMC firmware. The latest system software can be downloaded from http://support.intel.com/support/motherboards/server/S5000VCL/ Revision 2.2 41 Intel order number D71005-005

Section	Page
1. Introduction	9
1.1 System Views	9
1.2 System Dimensions	10
1.3 System Components	11
1.4 System Boards	13
1.5 Hard Drive and Peripheral Bays	13
1.6 Power Sub-System	15
1.7 System Cooling	15
1.8 Rack and Cabinet Mounting Options	15
2. Power Sub-System	16
2.1 Mechanical Overview	16
2.2 Output Connectors	17
2.2.1 P1 – Main Power Connector	17
2.2.2 P2 – Processor Power Connector	18
2.2.3 P3 – Baseboard Signal Connector	18
2.2.4 P4 and P5 – SATA Hard Drive Power Connectors	18
2.2.5 P6 – CD Power Connector	19
2.2.6 P7 – HSBP Power Connector	19
2.3 Efficiency	19
2.4 AC Input Voltage Requirement	19
2.5 Protection Circuits	20
2.5.1 Over-current Protection (OCP)	20
2.5.2 Over-voltage Protection (OVP)	20
2.5.3 Over-temperature Protection (OTP)	21
2.6 AC Power Cord Specification Requirements	21
3. Cooling Sub-System	22
3.1 Power Supply Fans	23
3.2 Processor Air Duct and Air Baffle	23
4. Peripheral and Hard Drive Support	25
4.1 Optical Drive Support	26
4.1.1 Optical Drive Support	26
4.2 Hard Disk Drive Support	27
4.2.1 Hot-Swap Hard Disk Drive Trays	27
4.2.2 Drive Blanks	28
4.2.3 System Fan Connectors	29
5. Front Control Panel	30
5.1.1 Power/Sleep LED	32
5.1.2 System Status LED	32
5.1.3 Drive Activity LED	33
6. PCI Riser Cards and Assembly	34
7. Backplane Board	35
7.1.1 Hard Drive Activity LED	37
8. Supported Intel® Server Boards	38
8.1 Intel® Server Board S5000VCL Feature Set	38
9. Environmental and Regulatory Specifications	39
9.1 System Level Environmental Limits	39
9.2 Serviceability and Availability	39
9.3 Replacing the CMOS Battery	40
9.4 Product Regulatory Compliance	41
9.5 Use of Specified Regulated Components	41
9.6 Electromagnetic Compatibility Notices	43
9.6.1 USA	43
9.6.2 FCC Verification Statement	44
9.6.3 ICES-003 (Canada)	44
9.6.4 Europe (CE Declaration of Conformity)	44
9.6.5 Japan EMC Compatibility	44
9.6.6 BSMI (Taiwan)	45
9.6.7 RRL (Korea)	45
9.7 Product Ecology Compliance	46
9.8 Other Markings	48
Appendix A: Integration and Usage Tips	49
Appendix B: POST Code Diagnostic LED Decoder	50
Appendix C: POST Error Beep Codes	54
Glossary	54