Invacare TDXSP Owners Manual - Page 54

Mode Switch CMPJ+ Joystick or On/Off - Mode Switch nXc Joystick, Memory Card Slot, When to Charge - tdx sp power wheelchair with tilt

Get Invacare TDXSP PDF manuals and user guides View all Invacare TDXSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

5 WHEELCHAIR OPERATION Mode Switch (CMPJ+ Joystick) or On/Off - Mode Switch (nXc Joystick) The mode switch is used to select the operating mode for the wheelchair. The mode switch is located on the joystick. A mode switch is needed whenever any of the following operating modes are programmed:.  *In these modes, Standby Select allows the reset switch to be bypassed for users unable to activate the switch. These modes are NOT available on wheelchairs with nXc joysticks - Environmental Controls, Digital 3 Speed, Sleep Mode and Remote Drive Selection Mode. • Environmental Controls (ECU 1, ECU 2, ECU 3, ECU 4)* • 3 Speed Mode in Digital 3 Speed (Slow, Medium, Full) • Sleep Mode • RIM Mode* • Remote Drive Selection Mode* • Tilt/Recline Mode* • Information Center Display Selection (does not require Reset activation at power up). Refer to User Settings on page 51. If any of the above modes are selected, the control will require activation of the switch immediately after the power switch is turned On in order to enter the drive mode. The second line of the LCD will display - PRESS RESET. Memory Card Slot The memory card slot is used with the basic or professional memory card for saving or reading wheelchair parameters. 5.5 When to Charge Batteries  Keep Batteries charged. When possible, DO NOT allow battery charge to empty. If battery charge becomes so low that no battery indicators are lit, allow the batteries to charge overnight. Invacare® TDX®SP, TDX SR 54 Part No 1143190

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
5
WHEELCHAIR OPERATION
Invacare® TDX®SP, TDX SR
54
Part No 1143190
Mode Switch (CMPJ+ Joystick) or On/Off - Mode Switch (nXc Joystick)
The mode switch is used to select the operating mode for the wheelchair. The mode switch is located on the joystick. A mode switch is needed
whenever any of the following operating modes are programmed:.
•
Environmental Controls (ECU 1, ECU 2, ECU 3, ECU 4)*
•
3 Speed Mode in Digital 3 Speed (Slow, Medium, Full)
•
Sleep Mode
•
RIM Mode*
•
Remote Drive Selection Mode*
•
Tilt/Recline Mode*
•
Information Center Display Selection (does not require Reset activation at power up). Refer to User Settings
on page 51.
If any of the above modes are selected, the control will require activation of the switch immediately after the power switch is turned On in order to
enter the drive mode. The second line of the LCD will display - PRESS RESET.
Memory Card Slot
The memory card slot is used with the basic or professional memory card for saving or reading wheelchair parameters.
5.5
When to Charge Batteries
*In these modes, Standby Select allows the reset switch to be bypassed for users unable to activate the switch.
These modes are NOT available on wheelchairs with nXc joysticks - Environmental Controls, Digital 3 Speed, Sleep Mode
and Remote Drive Selection Mode.
Keep Batteries charged. When possible, DO NOT allow battery charge to empty.
If battery charge becomes so low that no battery indicators are lit, allow the batteries to charge overnight.