JVC 6032VSL Instruction Manual - Page 18

Basic Settings 7 Speaker distance-DISTANCE UNIT, FRNT DISTANCE, CNTR DISTANCE, SURR DISTANCE Select the unit to measure the distance between your listening position and speakers-"METER" or "FEET." After selecting the measuring unit, select the appropriate speaker distance for each speaker within the range of "0.3m" ("1FT") to "9.0m" ("30FT") by 0.3 m (1 foot) step. Example: In this case, set "FRNT DISTANCE" to "3.0m" ("10FT"), "CNTR DISTANCE" to "2.7m" ("9FT"), and "SURR DISTANCE" to "2.4m" ("8FT"). L C R 3.0 m (10 feet) 2.7 m (9 feet) 2.4 m (8 feet) 2.1 m (7 feet) LS RS • "METER" for the unit and "3.0m" ("10FT") for all speakers are the initial settings. Note: If you have selected "NONE" for the center and surround speakers setting, you cannot set the speaker distance for the center and surround speakers. 7 Crossover frequency-CROSSOVER Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to other large speakers. To use this function properly, set the crossover frequency according to the table below: Crossover frequency Size of cone speaker unit built in the small speaker 80HZ about 12 cm (4 3/4 inches) 100HZ about 10 cm (3 15/16 inches) (initial setting) 120HZ 150HZ about 8 cm (3 3/16 inches) about 6 cm (2 3/16 inches) 200HZ less than 5 cm (2 inches) • If you have selected "LARGE" for all speakers, this function will not take effect ("CROSS OFF" appears). 7 Dynamic range compression-D_COMPRESSION You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when using surround sound at night. • This function takes effect only when playing back a source using Dolby Digital. MID MAX OFF Select this when you want to reduce the dynamic range a little (initial setting). Select this when you want to apply the compression effect fully. (Useful at night.) Select this when you want to enjoy surround sound with its full dynamic range. (No effect applied.) Selecting the Digital Input Terminals- DIGITAL IN When you use the digital input terminals, register which components are connected to which terminals (DIGITAL 1/2) so that the correct source name will appear when you select the digital source. Select the appropriate option from the following: 1 DVD 2 CD O 1 DVD 2 TV O 1 DVD 2 CDR O 1 CD 2 DVD O 1 CD 2 TV O 1 CD 2 CDR O 1 TV 2 DVD O 1 TV 2 CD O 1 TV 2 CDR O 1 CDR 2 DVD O 1 CDR 2 CD O 1 CDR 2 TV O (back to the beginning) Note: When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components: • DIGITAL 1 (coaxial): For DVD player • DIGITAL 2 (optical): For CD player Selecting the Video Input Terminal- VIDEO IN DVD, VIDEO IN VCR RX-6030V RX-6032V ONLY This receiver is equipped with component video input terminals which give you higher picture quality for the DVD player and VCR. When you use the component video input terminals for the DVD player and/or VCR, change the video input terminal setting to use the AV COMPU LINK remote control system correctly (see page 30). COMPONENT S/C Select this when you connect the DVD player and/or VCR to the component video input terminals. Select this when you connect the DVD player and/or VCR to the S-video or composite video input terminal (initial setting). 7 Low Frequency Effect attenuator-LFE ATTENUATE If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS Digital Surround, select "-10dB" to activate the Low Frequency Effect attenuator. • This function takes effect only when the LFE signals come in. 0dB Normally select this (initial setting). -10dB Select this when the bass sound is distorted. 16