JVC DLA-S15U DLA-S15U User instruction manual (2.1MB) - Page 54

Maintenance

Get JVC DLA-S15U - D-ila Projector, 1:1 Fixed Lens PDF manuals and user guides View all JVC DLA-S15U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Symptom Probable cause Corrective action The upper part of the • While computer system signal is input, • Input separate sync signals for vertical video image bows or isn't a sync signal for composite sync sync (V) and horizontal sync (H) distorts. (Cs) or G on sync being input? signals. • Isn't signal with much jitter or skew • Input signals with little jitter or distor- distortion being input to a video deck? tion. • Is the source setting correctly selected? • Set the source setting to AUTO. If the Isn't a wrong source (forced mode) problem still persists, set it to the selected? correct dedicated source (forced mode). Video image and • Are video picture and audio turned off • Turn on video picture and audio by audio sound suddenly by pressing the AV MUTING button on pressing the remote control's AV go out. the remote control unit? MUTING. Remote control unit • Are batteries installed correctly? does not work. • Match the polarities of batteries correctly (+ to + and - to -). • Are batteries exhausted? • Replace with new batteries. • Is there a shielding object between the • Remove any shielding objects. remote control unit and the remote sensor? • Is the distance too long? • Use the remote control unit at a nearer point. Page 12 - 46 29 14 14 18 18 * This projector is equipped with a microcomputer that may operate abnormally due to interference from external components. If this happens, turn off the main power and disconnect the power cord from the wall AC outlet. Then reconnect the power cord to AC outlet and turn on the main power again. (For the turning on and off the power, see pages 25 to 26.) Maintenance • Stains on the cabinet Should be wiped off with a soft cloth. If the cabinet is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth. • Since the cabinet may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following: - Do not wipe it with a hard cloth. - Do not wipe it strong. - Do not wipe it with thinner or benzene. - Do not apply any volatile substance such as insecticides to it. - Do not allow any rubber or vinyl article to remain in contact with it for a long time. • Stains on the lens Sould be cleaned off with commercially available blowers or lens cleaning paper (for cleaning glasses and cameras). Do not use liquid cleaning agents. This could cause the surface coating to be removed. Do not rub or hit the lens as its surface is prone to damage. ENGLISH 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
53
ENGLISH
* This projector is equipped with a microcomputer that may operate abnormally due to interference from external components.
If this happens, turn off the main power and disconnect the power cord from the wall AC outlet. Then reconnect the power cord
to AC outlet and turn on the main power again.
(For the turning on and off the power, see pages 25 to 26.)
Symptom
Probable cause
Corrective action
Page
The upper part of the
video image bows or
distorts.
Video image and
audio sound suddenly
go out.
Remote control unit
does not work.
• While computer system signal is input,
isn’t a sync signal for composite sync
(Cs) or G on sync being input?
• Isn’t signal with much jitter or skew
distortion being input to a video deck?
• Is the source setting correctly selected?
Isn’t a wrong source (forced mode)
selected?
• Are video picture and audio turned off
by pressing the AV MUTING button on
the remote control unit?
• Are batteries installed correctly?
• Are batteries exhausted?
• Is there a shielding object between the
remote control unit and the remote
sensor?
• Is the distance too long?
• Input separate sync signals for vertical
sync (V) and horizontal sync (H)
signals.
• Input signals with little jitter or distor-
tion.
• Set the source setting to AUTO. If the
problem still persists, set it to the
correct dedicated source (forced
mode).
• Turn on video picture and audio by
pressing the remote control’s AV
MUTING.
• Match the polarities of batteries
correctly (+ to + and - to -).
• Replace with new batteries.
• Remove any shielding objects.
• Use the remote control unit at a nearer
point.
12
—
46
29
14
14
18
18
Maintenance
• Stains on the cabinet
Should be wiped off with a soft cloth. If the cabinet is heavily stained, wipe it with a cloth soaked in water-diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
•
Since the cabinet may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following:
– Do not wipe it with a hard cloth.
– Do not wipe it strong.
– Do not wipe it with thinner or benzene.
– Do not apply any volatile substance such as insecticides to it.
– Do not allow any rubber or vinyl article to remain in contact with it for a long time.
• Stains on the lens
Sould be cleaned off with commercially available blowers or lens cleaning paper (for cleaning glasses and cameras).
Do not use liquid cleaning agents. This could cause the surface coating to be removed.
Do not rub or hit the lens as its surface is prone to damage.