JVC RXD702B Instructions - Page 39
DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz
UPC - 046838019142
View all JVC RXD702B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
English Adjusting the equalization patterns- DIGITAL EQ 63Hz/250Hz/1kHz/4kHz/16kHz You can adjust equalization patterns in five frequency bands (center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the front speakers. • Once you have made an adjustment, it is memorized for each source. Adjustable range: -8 (dB) to +8 (dB) (in 2 dB intervals) Initial setting: 0 (dB) for all bands • When adjustment is made, the DIGITAL EQ indicator lights up on the display. If no adjustment is required, set all the frequency bands to "0 (dB)." • The DIGITAL EQ indicator goes off from the display. From the remote control: Before you start, remember... There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. 1 Press D. EQ FREQ repeatedly to select the band you want to adjust. 1 2 3 4 5 6 2 Press D. EQ LEVEL + or - to adjust the equalization pattern of the selected band. 7 8 9 10 0 10 1 2 3 Repeat steps 1 and 2 to adjust other bands. Adjusting the bass sounds 7 Reinforcing the bass-BASS BOOST You can boost the bass level-Bass Boost. • Once you have made an adjustment, it is memorized for each source. • You cannot adjust this item directly from the remote control. BASS BOOST: ON BASS BOOST: OFF Select to boost the bass level. The B.BOOST indicator lights up on the display. Select to deactivate the Bass Boost. Initial setting: BASS BOOST: OFF NOTE This function affects only the sound coming out through the front speakers. 7 Attenuating the input signal-INPUT ATT When the input level of analog source is too high, the sound will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion. • Once you have made an adjustment, it is memorized for each source. • You cannot adjust this item directly from the remote control. INPUT ATT: ON INPUT ATT: NORMAL Select to attenuate the input signal level. The INPUT ATT indicator lights up on the display. Select to deactivate attenuation. Initial setting: INPUT ATT: NORMAL Adjusting the sound parameters for the Surround/DSP modes You can adjust the Surround/DSP sound parameters to your preference. • For details about the Surround/DSP modes, see pages 41 to 43. 7 Adjusting the effect level for DSP modes -EFFECT This setting is available only when one of the DSP modes (except ALL CH STEREO) is in use. To activate DSP mode, see page 45. • Once you have made an adjustment, it is memorized for each DSP mode. Adjustable range: 1 to 5 (in 1 step intervals) Initial setting: EFFECT: 3 As the number increases, the effect becomes stronger. Normally, select "3." From the remote control: Press EFFECT repeatedly to select the level you want to adjust. 1 2 3 4 5 6 7 8 9 10 0 10 7 Adjusting the virtual room size for DSP modes -ROOM SIZE This setting is available only when one of the DSP modes (except ALL CH STEREO) is in use. To activate DSP mode, see page 45. • If "SURROUND SPK" is set to "NO" (see page 28), this item is not adjustable. • Once you have made an adjustment, it is memorized for each DSP mode. • You cannot adjust this item directly from the remote control. Adjustable range: 1 to 5 (in 1 step intervals) Initial setting: ROOM SIZE: 3 As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. Normally, select "3." 37