Jensen JGS8750BDS Use and Care Guide - Page 12

detected, the message FAULTDETECTED- PRESSPOWERTO CLEARor FAULT - code

Page 12 highlights

Oven will not self=clean. • Check to make sure the cycle is not set for a delayed start. See pg. 5. • Check if door is closed. • Check if control is in Sabbath Mode. See pg. 27. ° Oven may be over 400° F. Oven temperature must be below 400° F to program a clean cycle. Oven did not clean properly. • Longer cleaning time may be needed. • Excessive spillovers, especially sugary and/or acidic foods, were not removed prior to the self-clean cycle. Oven door will not unlock after self=clean cycle. ° Oven interior is still hot. Allow about one hour for the oven to cool after the completion of a self-clean cycle, The door can be opened when the LOCKED indicator word is not displayed, • The control and door may be locked, See pg. 15. There are no beeps and no display. Moisture collects on oven window or steam comes from oven vent= ° Oven may be in Sabbath Mode. See page 27. • This is normal when cooking foods high in moisture. • Excessivemoisture was used when cleaning the window. There is a strong odor or light smoke when oven is turned on. ° This is normal for a new range and will disappear after a few uses. Initiating a clean cycle will "burn off" the odors more quickly. • Turning on a ventilation fan will help remove the smoke and/or odor. • Excessivefood soils on the oven bottom. Use a self-clean cycle. Fault Codes • The oven may detect a fault during programming or during operation. If a fault is detected, the message FAULT DETECTED- PRESSPOWERTO CLEAR or FAULT DETECTED- PRESSENTERTO TRY AGAIN may appear. Follow directions in the display. If the fault reappears or does not clear, call an authorized servicer or the toll-free number in the display. ° If the same operation is attempted before having the oven repaired, the message FEATURENOT AVAILABLE will appear. The feature will remain inoperable until service is obtained. • If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning. Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the clean cycle. If the fault code reappears, contact an authorized servicer. Noises may be heard. • The oven makes several low-level noises. You may hear the oven relays as they go on and off. This is normal. • As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This is normal and will not damage your appliance. SAb flashing and then displayed continuously, ° Oven isin Sabbath Mode. To cancel, press and hold the Setup pad for five seconds. Cannot add another Favorite. • Favorites is full. To delete a favorite and add another, see page 25. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

Oven
will
not
self=clean.
Oven did
not
clean properly.
Oven door will
not
unlock
after
self=clean cycle.
There are
no beeps and
no
display.
Moisture
collects on oven
window or steam comes
from
oven
vent=
There is
a
strong odor or light
smoke when oven is
turned
on.
Fault Codes
Noises
may be heard.
Check to make sure the cycle is not set for a delayed start. See pg. 5.
Check if door is closed.
Check if control is in Sabbath Mode. See pg. 27.
°
Oven may be over 400° F. Oven temperature must be below 400° F to program a
clean cycle.
Longer
cleaning time may be needed.
Excessive spillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
°
Oven
interioris
still hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle, The door can be opened when the LOCKED
indicator word is not displayed,
The control and door may be locked, See pg. 15.
°
Oven may be in Sabbath Mode. See page 27.
This
is
normal when cooking foods high in moisture.
Excessivemoisture was used when cleaning the window.
°
This
is
normal for a new range and will disappear after a few uses. Initiating a clean
cycle will "burn off" the odors more quickly.
Turning on a ventilation fan will help remove the smoke and/or odor.
Excessivefood soils on the oven bottom. Use a self-clean cycle.
The oven may detect a fault during programming or during operation. If a fault is
detected, the message FAULTDETECTED- PRESSPOWERTO CLEARor FAULT
DETECTED- PRESSENTERTOTRY AGAIN may appear. Follow directions in the display.
If the fault reappears or does not clear, call an authorized servicer or the toll-free
number in the display.
°
If the same operation is attempted
before
having the oven repaired, the message
FEATURENOT AVAILABLE will appear. The feature will remain inoperable until service
is obtained.
If the oven is heavily soiled, excessive flareups may result in a fault code during
cleaning. Press the
CANCEL
pad and allow the oven to cool completely, wipe out
excess soil, then reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
The oven makes several low-level noises. You may hear the oven relays as they go on
and off. This is normal.
As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
SAb
flashing
and then
°
Oven
isin
Sabbath Mode. To cancel, press and hold the
Setup
pad for five
displayed
continuously,
seconds.
Cannot
add another
Favorite.
Favorites is full. To delete a favorite and add another, see page 25.
11