Jensen JiMS 220 User Guide - Page 8

14

When the unit is at the power off mode.

Set Clock

1. Press the

MODE

button 3 times, the clock display flashes.

2.

To set the hour, press the

/

button to set advance or reverse hour setting.

Press and hold the button for fast advance / reverse value.

3.

To set the minute, press the

VOLUME + / -

button to set advance or reverse minute setting.


Set 12/24 Hour format

4. Press the

MODE

button again to enter 12/24 hour format setting mode.

5.

To select 12/24 hour format, press either the

/

button.

Set Year

6. Press the

MODE

button again to enter the year setting mode, the year reading flashes.

7.

To set year, press the

/

button to set advance or reverse the year.


Set Month/Date

8. Press the

MODE

button again to enter the month/date setting mode, the month/date reading flashes.

9.

To set Month, press the

/

button to set advance or reverse the month.


10. To set Date, press the

VOLUME + / -

button to set advance or reverse date.


Exit setting mode

11.

To save all settings and exit the setting mode, press the

MEM

button.

CLOCK AND CALENDAR SETTINGS

This unit provides an auxiliary audio signal input for connecting external audio devices.

Use the included audio cable with 3.5 mm stereo plug to connect the external device to the AUX IN Jack

located on the back of the unit.

AUXILIARY INPUT

1. Pull out the audio AUX LINE-IN cable located on the back of the unit and extend it to a desired length.

2. Connect the 3.5mm

AUX IN stereo plug

to the line out jack or Headphone jack of your external

audio device

3. Press the

POWER

button to turn on the unit.

4. To select auxiliary audio input, press

the

FUNCTION

button.

“AUX” indicator show on display.

5. Turn on the auxiliary device.

6. The volume and equalizer can now be controlled through the main

unit. Operate all other functions on the auxiliary device as usual.

To external auxiliary device

Note:

(1) If you connected the Line Out Jack of your external device then you

only need to adjust the volume control of this unit. If you connected

the Headphone Jack of your external device then you may need to

adjust both the volume control of your external device and the volume

control of this unit to find the most desirable volume setting.

(2) Press the

POWER ON / OFF

button turning off the unit when you

finish listening.

Don't forget to switch off the power of your external device as well.

13

The unit has 4 preset EQ settings for your selection.

In either RADIO, iPod, CD or AUX modes:

To select preset EQ: ROCK, CLASSIC, POP or JAZZ ; press

EQ

button.

The corresponding indicator shows on

.

display

EQ SETTING

iPod OPERATIONS

If the docking port will not be used for an extended period of time, it is recommended to push-close the iPod

docking drawer to cover the docking port and prevent damage.

1. Push-Open the iPod docking drawer.

2. Use the iPod adapter included with your iPod and insert it into the docking area. Your iPod can now be

inserted into the docking port by placing the

connector on the bottom of the iPod onto the connector in

the docking bay.

Note

- Please be careful when seating the iPod into the docking to avoid

damaging the 30-pin connector on the iPod or in the docking

system.

3. Press the

POWER

button to turn on the unit.

4. Press the

FUNCTION

button to select iPod mode. The iPod will start playing automatically and start

charging immediately.

5. Press

the

PLAY / PAUSE

button to pause or resume iPod playback.

6.

Adjust the sound level by pressing the

VOLUME + / -

button.

Note : The volume level cannot be adjusted using the volume control on your iPod after being

docked.

7

. The iPod charges even during playback.

Note : The iPod will only charge in iPod, AUX or power “OFF” modes.

8

. To remove the iPod from the unit, press and hold the

PLAY/PAUSE

button

for three seconds to switch

off the device and then gently remove it from

the docking connector.

9. Gently push the iPod docking drawer back into the unit and locked.

iPod playback control:

- Press the

PLAY/PAUSE

button to pause or resume the iPod playback;

- Press the Skip/Search Forward

or Backward

button to skip to

the next or previous song;

- Press and hold the Skip/Search Forward

or Backward

button

for fast-forwarding or fast-rewinding

during playback.

Jensen JiMS 220 User Guide - Page 8

Clock And Calendar Settings, Auxiliary Input, Eq Setting, Ipod Operations - docking

Page 8 highlights

Section	Page
	1
	2
	3
	4
	5
	6
	7
	8
	9