Jensen VM9022HD Operation Manual - Page 10

Installing the MediaLink External AV, Connector - installation

Get Jensen VM9022HD - AM/FM HD Radio PDF manuals and user guides
UPC - 043258304292
View all Jensen VM9022HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

CAUTION! Be careful not to damage the car wiring. 5. Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch. The 4 tabs on the trim ring will snap into four holes on top and bottom of the mounting sleeve. TRIM RING MOUNTING SLEEVE OPTIONAL MTORUIMNTRIINNGG SLEEVE M3x4 SCREW After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 1. Connect wiring adapter to existing wiring harness. 2. Connect antenna lead. 3. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place. Using the Cosmetic Trim Ring Two cosmetic trim rings are packaged with the VM9022HD for installation flexibility. The VM9022HD will fit into most import dashes with little or no modification to the dash board/ cavity. Some US domestic vehicle dashes will accept a Double-DIN chassis, but there is usually a small gap between the radio and dash piece after installation is complete. In this case, use the appropriate trim ring to conceal any gaps that may be present. Installing the MediaLink External AV Connector The MediaLink allows you to connect a variety of external devices, including a VCR, DVD player, portable MP3 player, etc., to your VM9022HD without removing the radio. To install the MediaLink, connect it to the AUX-IN cables on the back of the VM9022HD (see the Wiring Diagram on page 3), and then install the MediaLink in a location convenient for plugging in auxiliary devices. Replacing the Fuse When replacing the fuse, use a new 20A replacement fuse. Using a fuse with an improper rating could damage the unit and cause a fire. 6 VM9022HD

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
6
VM9022HD
CAUTION! Be careful not to damage the car wiring.
5.
Complete wiring as illustrated in the wiring diagram on
page 3. Once the wiring is complete, reconnect the
battery negative terminal. If there is no ACC available,
connect the ACC lead to the power supply with a switch.
After completing the wiring connections, turn the unit on to
confirm operation (ignition switch must be on). If unit does not
operate, recheck all wiring until problem is corrected. Once
proper operation is achieved, turn off the ignition switch and
proceed with final mounting of the chassis.
1.
Connect wiring adapter to existing wiring harness.
2.
Connect antenna lead.
3.
Carefully slide the radio into the half-sleeve, making
sure it is right-side-up, until it is fully seated and the
spring clips lock it into place.
Using the Cosmetic Trim Ring
Two cosmetic trim rings are packaged with the VM9022HD
for installation flexibility. The VM9022HD will fit into most
import dashes with little or no modification to the dash board/
cavity. Some US domestic vehicle dashes will accept a
Double-DIN chassis, but there is usually a small gap between
the radio and dash piece after installation is complete. In this
case, use the appropriate trim ring to conceal any gaps that
may be present.
The 4 tabs on the trim ring will snap into four holes on top and
bottom of the mounting sleeve.
Installing the MediaLink External AV
Connector
The MediaLink allows you to connect a variety of external
devices, including a VCR, DVD player, portable MP3 player,
etc., to your VM9022HD without removing the radio.
To install the MediaLink, connect it to the AUX-IN cables on
the back of the VM9022HD (see the Wiring Diagram on page
3), and then install the MediaLink in a location convenient for
plugging in auxiliary devices.
Replacing the Fuse
When replacing the fuse, use a new 20A replacement fuse.
Using a fuse with an improper rating could damage the unit
and cause a fire.
MOUNTING SLEEVE
M3x4
SCREW
TRIM RING
MOUNTING
SLEEVE