Kenmore 33205 Owners Manual - Page 20

Minimum 12 in. (30 cm) r'_ from soffit'_---_L ' _ to side or 12 in. (30 cm) l-k_ ibovedoor Minimum\ _ _ / li imul , 7 ft. (2.3 m) _. _ I _ _k,_ above " _"_' I L J._ /2 ft. (61 cml //from outsiae public sidewalk I I r_r "Ix _ / corner ___ orpaved _ N \1 \ \\ / / __ __XI _ Minim•um 3 ft. (91 cm) a12o_/_(30_n) r expected snowfall J Minimum 3 ft. (91 cm) within a height of 15 ft. (4.6 m) above meter/regulator assembly _ __ , Minimum 3 ft. ( 91 cm ) clearance /to service regulator vent outlet ___\7__,,._ [_. kX_k_ _._X,"t //_ _....._ ["-- I /I I / I I /_ I Minimum 12 in. (30 cm) I under veranda, porch, I .deck or balcony _ (seefootnote 1) (seder_Vetwnay 2) _ i /N \ \\ I I / _XI_.--_ "_'-_. I 12Mi/?lfl_m) Minimum 4_. (1.2 m)_'_ __ _ Jt / L_ 1 CLW_ / _-[X] 1 / _, _E / _ i __ /_ i- "_ _ I-- _ _ L_, /_..__ _)\ I- \ _/ _.\X J..._'X_ / _ I% _/ _ __ F- ./I _'_ Mai'nb9(r__Uvmeam ) mechanical air supply inlet within l0 ft. (3 m) I..,,..'_--"1 horizontally \ _ Minimum 4 ft. (1.2 m) _°mm_idenSt_yffr_h_¢imdey°bfedW°wop __ closed window Minimum 12 in. (30 cm) above window or door that may be open Minimum 4 ft. (1.2 m) below a window that may be open MiTAmum4_t_il"2mw) bela_W°rSiode°_J2a_Gc_OCm) o s ae o ao supply inlet into building that may be open or combustion air inlet to another appliance [] VENT TERMINAL (_) AIR SUPPLY INLET [] AREA WHERE TERMINAL IS NOT PERMITTED 1. Permitted only if veranda, porch, deck or balcony is fully opened on a minimum of two sides beneath the floor. 2. A vent shall not terminate above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings. FIGURE 23. This unit can vent through 2", 3" or 4" nonmetallic pipe and fittings. The vent pipe installation can be started from either the blower discharge or the termination wall. Keep in mind the total vent system (pipe and elbows) when installing the vent system, see VENTING AND INSTALLATION AND MAXIMUM VENT LENGTHS, page 17. MORTAR OR SILICONE CAULK FROM WATER HEATER _;t. i _; 4.! WALL PLATE (OPTIONAL) J TERMINAL WITH MESH PVPCROVTEENCTTIVE _N INSIDE VERTICAL VENT TERMINATION RESTRICTIONS 1. Minimum of twelve 12" (30.5 cm) above the roof or twelve 12" (30.5 cm) above the anticipated snow level. Provide proper support for all pipe protruding through the roof. VENT TERMINAL /--ROOF / _0.5 C_RA) BOVEROOF II MIN°OF 12"(30.5cm)ABOVE I I ANTICIPASTNEODWLEVEL PVC COUPLING '_ ° _ 12" MIN.(30.5 cm) • °. i _1_ BUOILUDTISNIGDE WOAFLL L FIGURE 24. The vent terminal should be kept as close as possible to the outside wall, but you need to allow at least 1.5" (3.8 cm) of pipe past the wall, for the wall flange and vent terminal to mount on the pipe. Before the vent terminal is installed, caulk (not supplied) around the pipe on the exterior wall and install the optional wall flange. The flange can be held to the outside wall by placing some of the caulking on the back of the flange. The wall flange is supplied for decorative purposes only and is not a requirement for the vent termination (if not needed by the installer). VERTICAL VENT THROUGH ROOF This unit is approved for venting through the roof with the type vent terminal that is included with the unit. A proper flashing or "BOOT" should be used to seal the pipe where it exits the roof. The total vent system should not exceed that which is specified, see VENTING AND INSTALLATION, page 17. *ALL PIPE PROTRUDING THROUGH THE ROOF SHOULD BE PROPERLY SUPPORTED. FIGURE 25. 2. 4' (1.2 m) from or 1' (0.3 m) above any gable, dormer, or other roof structure with access to interior of building (i.e.-vent, window etc.). All of the pipe should be secured as per the instructions in the instructions in the VENTING AND INSTALLATION, page 17. 3. 3' (0.9 m) above any forced air inlet located within 10' (3.0 m). 20