Kenmore 4751 Use and Care Guide - Page 22

Kenmore 4751 - 3.6 cu. ft. HE2 Manual

Get Kenmore 4751 - 3.6 cu. ft. HE2 PDF manuals and user guides
UPC - 883049129334
View all Kenmore 4751 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

To transport Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are found. When replacing your inlet hoses, record the date of replacement. 1. the washer: If washer will be moved during freezing weather, put in 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Drain & Spin cycle. Unplug the power cord. Disconnect the drain hose from the drain system and attach to rear panel clips. Shut off both water faucets. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the rear panel of the washer. IMPORTANT: Call service. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician. Reinstalling the washer Instructions" to locate, level and 2. 3. Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer. If storing or moving your washer during freezing weather, winterize it. Non-use or vacation care: Operate your washer only when you are at home. If you will be on vacation or not using your washer for an extended period of time, you should: Unplug washer or disconnect power. 4. 5. 6. Turn off the water supply to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away. • Slightly open door to provide ventilation. 1. 2. Follow the "Installation connect the washer. To winterize washer: 1. 2. 3. 4. 5. Put 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Drain & Spin cycle. Unplug washer or disconnect power. Shut off both water faucets. Disconnect water inlet hoses from faucets and drain. To use washer 1. 2. 3. again: Run the washer through the Normal/Casual cycle to clean the washer and remove the antifreeze, if used. Use only HE High Efficiency detergent. Use 1/2of the manufacturer's recommended amount for a medium-sized load. Flush water pipes. Reconnect water inlet hoses to faucets. Turn on both water faucets. Electrical Plug into a grounded Do not remove ground Do not use an adapter. Do not use an extension Shock Hazard 3 prong outlet. prong. cord. can result in death, Failure to follow these instructions fire, or e_ectrical shock. Plug in washer or reconnect power. 4= 5. Run the washer through the Normal/Casual cycle. Use only HE High Efficiency detergent. Use 1/2 of the manufacturer's recommended amount for a medium-sized load. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Replace
inlet hoses after 5 years
of use to reduce
the risk of hose
failure. Periodically
inspect
and replace
inlet
hoses if bulges,
kinks,
cuts, wear or leaks are found.
When replacing
your
inlet hoses,
record the date of replacement.
Install and store
your washer
where
it will not freeze.
Because
some water
may stay in the hoses, freezing
can damage
your
washer. If storing
or moving
your washer
during
freezing
weather,
winterize
it.
Non-use
or vacation
care:
Operate your washer
only when you are at home.
If
you will be on
vacation
or not using your washer
for an extended
period
of time,
you should:
Unplug
washer
or disconnect
power.
To transport
the washer:
•
Slightly
open
door to provide
ventilation.
1.
If washer
will be moved
during freezing
weather,
put in 1 qt
(1 L) of R.V.-type
antifreeze
in the drum.
Run washer
on a
Drain & Spin cycle.
2.
Unplug
the power
cord.
3.
Disconnect
the drain
hose from the drain
system
and attach
to rear panel clips.
4.
Shut off both water
faucets.
5.
Disconnect
the water
inlet hoses from faucets,
then drain the
hoses
and clip them to the rear panel
of the washer.
6.
IMPORTANT:
Call service.
Do not reuse transport
bolts.
Washer
must be transported
in the upright
position.
To avoid
suspension
and structural
damage,
your machine
must be
properly
set up for relocation
by a certified
technician.
Reinstalling
the washer
Turn off the water
supply
to the washer. This helps avoid
accidental
flooding
(due to a water
pressure
surge) while you
1.
are away.
2.
To winterize washer:
1.
Put 1 qt (1 L) of R.V.-type
antifreeze
in the drum.
2.
Run washer
on a Drain & Spin cycle.
3.
Unplug
washer
or disconnect
power.
4.
Shut off both
water faucets.
5.
Disconnect
water
inlet hoses from faucets
and drain.
To use washer
again:
1.
Flush water
pipes.
2.
Reconnect
water
inlet hoses to faucets.
3.
Turn on both water
faucets.
Follow
the "Installation
Instructions"
to
locate,
level and
connect
the washer.
Run the washer
through
the Normal/Casual
cycle to clean the
washer
and remove
the antifreeze,
if used.
Use only HE High
Efficiency
detergent.
Use 1/2of the manufacturer's
recommended
amount
for a medium-sized
load.
Electrical
Shock
Hazard
Plug into
a grounded
3
prong
outlet.
Do not
remove
ground
prong.
Do not
use an adapter.
Do not
use an extension
cord.
Failure
to follow
these
instructions
can result
in
death,
fire,
or e_ectrical
shock.
4=
5.
Plug in washer
or reconnect
power.
Run the washer
through
the Normal/Casual
cycle.
Use only
HE High Efficiency
detergent.
Use 1/2of the manufacturer's
recommended
amount
for a medium-sized
load.
22