Kenmore 4751 Use and Care Guide - Page 6

Kenmore 4751 - 3.6 cu. ft. HE2 Manual

Get Kenmore 4751 - 3.6 cu. ft. HE2 PDF manuals and user guides
UPC - 883049129334
View all Kenmore 4751 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Selecting theproper location foryour washer improves performance andminimizes noise andpossible washer "walk." Your washer canbeinstalled under acustom counter, orina basement, laundry room, closet, orrecessed area. See "Drain System." Companion appliance location requirements should also be considered. Proper installation isyourresponsibility. You will need • • A water heater set to deliver 120°F (49°C) water to the washer. A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. A sturdy and solid floor to support the washer with a total weight (water and load) of 400 Ibs (180 kg). Recommended installation undercounter installation The dimensions spacing for custom shown are for the recommended spacing. Custom undercounter installation - Washer only ( 3T mir_. (93.9 cm} (2.5 cm} (68,6 cm} (2.5 cm) • Recommended installation spacing for recessed closet installation, with or without a pedestal The dimensions shown are for the recommended Recessed area or closet installation or • spacing. • Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Installation • • clearances 46 in? _,_ (3!0 cm2) The location must be large enough to allow the washer door to be fully opened. Additional spacing should be considered for ease of installation and servicing. The door opens more than 90 ° , and it is not reversible. Additional clearances might be required for wall, door, and floor moldings. Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer. Companion appliance spacing should also be considered. --_1 _" I_- 80v2" _1 4" I_-(2.5cm) (77,5crn) (10.2c_) 24in.2..._ (!66 cm2) • • • A B A. Side view - closet or confined area B. Closet door with vents Washer Dimensions 27" * Min. top and bottom air openings for closet door. Recessed or closet installation - Washer on pedestal 601/4" (127,6cm) (68.6 cm) 36" (9!,4 cm) 301/2" _/f (77,5cm) 1" --_1 I_-(2.5 cm) 27" -_4 I_-(68.6cm} !" (2.5cm) --_1 !"_ (2.5 cm) 3ov=" _q 4" I_(77.5 cm) (10.2cm} A Door is not reversible. B A. Recessed area B. Side view - closet or confined area

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Selecting
theproper
location
foryourwasher
improves
performance
andminimizes
noiseandpossiblewasher
"walk."
Yourwasher
canbeinstalled
underacustomcounter,
orina
basement,
laundry
room,closet,orrecessed
area.See"Drain
System."
Companion
appliance
location
requirements
shouldalsobe
considered.
Proper
installation
isyourresponsibility.
You will need
•
A water
heater set to deliver 120°F (49°C) water to the washer.
•
A grounded
electrical
outlet
located
within
6 ft (1.8 m) of
where the power
cord
is attached
to the back of the washer.
See "Electrical
Requirements."
•
Hot and cold water
faucets
located
within
4 ft (1.2 m) of the
hot and cold
water fill valves, and water
pressure
of
20-100
psi (137.9-689.6
kPa).
•
A level floor with
a maximum
slope
of 1" (2.5 cm) under entire
washer.
Installing
the washer
on soft floor surfaces,
such as
carpets
or surfaces
with foam
backing,
is not recommended.
•
A sturdy
and solid floor to support
the washer
with a total
weight
(water and load) of 400 Ibs (180 kg).
Do not operate
your
washer
in temperatures
below 32°F (0°C).
Some water
can remain
in the washer
and can cause
damage
in
low temperatures.
Installation
clearances
•
The location
must
be large enough
to allow the washer
door
to be fully opened.
•
Additional
spacing
should
be considered
for ease of
installation
and servicing.
The door opens
more than 90°, and
it is not reversible.
•
Additional
clearances
might
be required
for wall, door, and
floor moldings.
•
Additional
spacing
of 1" (2.5 cm) on all sides of the washer
is
recommended
to reduce
noise transfer.
•
Companion
appliance
spacing
should
also be considered.
Washer Dimensions
601/4"
(127,6cm)
27"
(68.6 cm)
Recommended
installation
spacing
for
custom
undercounter
installation
The dimensions
shown
are for the recommended
spacing.
Custom
undercounter
installation
-
Washer
only
(
3T
mir_.
(93.9 cm}
(2.5 cm}
(68,6 cm}
(2.5 cm)
Recommended
installation
spacing
for
recessed
or
closet
installation,
with
or without
a pedestal
The dimensions
shown
are for the recommended
spacing.
Recessed
area or closet installation
--_1 _" I_- 80v2"_1
4" I_--
(2.5cm)
(77,5crn)
(10.2c_)
A
46 in? _,_
(3!0 cm2)
24in.2..._
(!66 cm2)
B
A. Side view
-
closet
or confined
area
B. Closet door
with
vents
* Min. top and bottom
air openings
for closet
door.
Recessed
or closet
installation
-
Washer
on pedestal
36"
(9!,4 cm)
301/2"
_/f
(77,5cm)
Door
is not reversible.
1" --_1 I_--
27" -_4 I_--
!"
--_1 !"_
3ov="_q
4"
I_-
(2.5
cm)
(68.6cm}
(2.5cm)
(2.5cm)
(77.5
cm)
(10.2cm}
A
B
A. Recessed area
B. Side view
-
closet or confined area