Kenmore 75085 Owners Manual - Page 10

DepthDoftheexisting, wallsleeveinches, LengthA, inches

Get Kenmore 75085 - 8,000 BTU Single Room Thru-The-Wall Air Conditioner PDF manuals and user guides View all Kenmore 75085 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

PROCEDURE C H edirect the louvers at the back of the wall sleeve to 60 ° angle as shown in the FIG 16. The use of pliers is recommended. Rear Louvers 7 3/32" ;--------&too (Top View) _1 Remove the backing from the Horizontal Insulation strip 237/32 X 13/8 X 13/18 and attach that to the inside right of the sleeve as shown below. Remove the backing from the Around Insulation strip 5927/32 X 13/8x 13/8and attach that to the inside front of the sleeve as shown below. Indoor Outdoor FIG. 16 _'_lf the wall sleeve already has a rear grille, skip to step 4. If the wall sleeve does not have a rear grille or Iouvered panel, install the plastic grille from the kit. Cut the plastic grille to 26-1/2" wide and 15-1/2" high. Place the plastic grille to the inside of the wall sleeve at the rear flange. 8 1/2" FIG. 19 _"_ Iofrtheequdael pttoh 1o8f",yosukripetxoisstitnegp s7l.eOevtheeriws islees,s tchuatn the baffles and the support blocks according to Length "A" in the table below. Place the plastic grille FIG. 17 Depth"D"ofthe existing Length"A" wallsleeve(inches) (inches) 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
PROCEDURE
C
H
edirect the louvers at the back of the wall
sleeve to 60 ° angle as shown
in the FIG 16.
The use of pliers
is recommended.
7
3/32"
;--------&too
Rear Louvers
(Top View)
FIG. 16
_'_lf
the wall sleeve
already has a rear grille, skip
to step 4. If the wall sleeve does not have a rear
grille or Iouvered panel, install the plastic grille
from the kit. Cut the plastic grille to 26-1/2" wide
and 15-1/2" high. Place the plastic grille to the
inside of the wall sleeve at the rear flange.
Place the plastic grille
FIG. 17
_1
Fasten the 4 washer screws
to secure the grille
to the wall sleeve.
If you need plastic nuts to
mount plastic grille to the inside of the wall
sleeve, there are plastic nuts in the installation
kit. The nuts are installed from the inside of the
sleeve
and are pressed
into the square
holes of
the rear flanges.
or
Fasten the screws
FIG. 18
_1
Remove the backing from the Horizontal
Insulation strip
237/32
X 13/8 X 13/18
and attach
that to the inside right of the sleeve as shown
below. Remove the backing from the Around
Insulation strip
5927/32
X
13/8x 13/8and attach
that to the inside front of the sleeve
as shown
below.
Indoor
Outdoor
8
1/2"
FIG. 19
_"_
If the depth of your existing
sleeve
is less than
or equal to 18", skip to step 7. Otherwise,
cut
the baffles and the support
blocks according
to
Length "A" in the table below.
Depth"D"oftheexisting
wallsleeve(inches)
18 <D_<18-%
18-% <D_<19-3/4
19-3/4<D _<22
Length"A"
(inches)
3/4
1-3/4
4
--
upport
Block
_
Baffle
FIG.
20
r_
Remove the backing from the support
blocks
and attach them to the inside of the wall sleeve
as shown
FIG 21. Slide the baffle into slots of
the support
blocks
Wall
Wall
Sleeve
7
3/32")
Block
FIG. 21
-10-