Kenmore 7748 Use and Care Guide - Page 22

General

Care & Cleaning

(cont'd)

Cleaning

the

ContouredWell

Areas,

Burner

Cap,

Burner

Head

and

Burner

Drip Pans

(some

models)

The contoured

well areas, burner cap, burner head and burner drip pans (some models) should be routinely cleaned.

Keeping the burner ports clean will prevent improper

ignition and an uneven flame.

Refer to the following

instructions:

Surface

Burner

Grate

To Clean the Recessed

and Contoured

Areas

of the Cooktop

- If a spill occurs

on or in the recessed or contoured

areas, blot up spill with an absorbent

cloth.

Rinse with a clean, damp cloth and wipe dry.

<J.><.

ca

Burner

Cap

Surface

/

Burner

///

Head

//

Orifice

Holder?_

c rode

/

Ele

_

_)

Removable

Burner

Drip

Pan

{on

some

models)

To Remove

and Replace the Surface

Burner

Caps and Surface

Burner

Heads

= Remove

in the following

order: (1 st) surface burner grate, (2nd) surface burner

cap, (3rd) surface burner head and (4th) surface burner drip pan (if equipped).

Reverse the procedure above to replace the surface burner cap, surface burner

head and surface burner drip pans (if equipped).

Do not remove

any parts from

the

cooktop

until

they

have completely

cooled

and are

safe

to handle.

Do not

operate

the surface

burners

without

the surface

burner

cap and surface

burner

head

properly in place.

To Clean the Surface

Burner

Cap, Surface

Burner

Head and Surface

Burner

Drip Pan (if equipped)

-

Use a soap-filled

scouring pad or a mild abrasive

cleanser to clean the surface burner caps, surface burner heads and surface

burner drip pans (if equipped).

The ports (or slots) around the burner head must be

routinely cleaned.

If residue still remains

in these ports, use a small-gauge

wire or

needle to clean the slots or holes. For proper flow of gas and ignition of the

burner--DO

NOT ALLOW

SPILLS,

FOOD, CLEANING

AGENTS

OR ANY

OTHER

MATERIAL

TO ENTER THE GAS ORIFICE

HOLDER

OPENING.

ALWAYS

keep the surface burner cap and surface burner head in place whenever

a surface burner is in use.

Adjusting

the

Oven

Temperature

Your oven control has been precisely set at the factory. This setting may differ from your previous oven however, so your recipe

times may not give you the results you expect. If you think that the oven

is

cooking

too hot or too cool for your recipe times,

you can adjust the control so that the oven cooks hotter or cooler than the temperature

displayed.

To Adjust

Oven Temperature:

1.

Press

Bake

2.

Set the temperature

to 550°F (287°C) by pressing and holding the A.

3.

Within 2 seconds, pressand

hold B_e untilthe2digitdisplayappears.

Release B_ke.Thedisplaynowindicatestheamount

of degrees offset between the original factory temperature

setting and the current temperature

setting. If the oven control

has the original factory calibration,

the display will read "0."

4.

Thetemperaturecann_wbeadjustedup_rd_wn35°F(17°C)_in5°Fstepsbypressingandh_ldingthe

A

or V.Adjust

until the desired amount of offset appears in the display. When lowering the oven temperature,

a minus sign (-) will appear

before the number to indicate that the oven will be cooler by the displayed

amount of degrees.

5.

When you have made the desired adjustment,

press

_

to go back to the time of day display.

Note: Oven temperature

adjustments

made will not change the Self-Cleaning

feature temperature.

22

Kenmore 7748 Use and Care Guide - Page 22

<J.><.

Page 22 highlights